登录
首页 » matlab » kmeans

kmeans

于 2015-06-08 发布 文件大小:68KB
0 234
下载积分: 1 下载次数: 38

代码说明:

  kmeans算法,对交通路标进行Kmeans聚类分析,有GUI界面(kmeans algorithm, the traffic signs were clustered by using kmeans algorithm, GUI interface is available.)

文件列表:

kmeans

......\kmeansshow.m,1283,2008-05-15
......\kmeans_hhl.fig,10987,2014-05-12
......\kmeans_hhl.m,10959,2015-05-17

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • altitude-control
    四旋翼无人机的PID高度控制matlab仿真(Four-rotor UAV simulation matlab height control)
    2014-12-27 21:18:19下载
    积分:1
  • basic
    一个对初学matlab的人很有用的视频学习资料,让初学者在短时间学习matlab界面(matlab study )
    2009-11-05 16:44:16下载
    积分:1
  • Digital-filter
    设计低通数字滤波器,要求在通带内频率低于 时,允许幅度误差在1dB以内,(Design of digital low pass filter, requirements in the passband frequencies below, allow a margin of error of less than 1dB,)
    2012-04-20 17:19:11下载
    积分:1
  • CRLB
    一个关于克拉美罗界的代码,其中没有关于费舍尔矩阵的问题(CRB code on which there is no question about the Fisher matrix)
    2020-11-29 23:09:28下载
    积分:1
  • tuxiangchuli
    使用matlab语言对图像进行腐蚀操作,简单明了(The image using matlab language erosion operation, simple)
    2011-05-16 10:30:28下载
    积分:1
  • GPSchengxu
    GPS仿真程序。很好的。用MATLAB实现仿真过程。(GPS Simulation code)
    2010-05-24 20:48:16下载
    积分:1
  • powerflow
    对于大电网潮流计算的一些matlab程序,来源《大电网快速稳定分析关键基础技术研究(Power flow calculation for large number of matlab program, the source of " big power and rapid analysis of key infrastructure technology)
    2010-06-02 14:20:54下载
    积分:1
  • RSquare
    R-Square Feature Evaluation program implemented in matlab
    2015-01-20 06:00:47下载
    积分:1
  • bulangyundong2
    matlab 程实 实现布朗运动 源程序(matlab source Brownian motion process to achieve real)
    2011-08-02 11:27:16下载
    积分:1
  • Sine-wave
    单一频率的正弦相关法动态测试系统的测试方法简单,不需要对系统进行辨识。只需要观察被测系统输出信号的相差和幅值变化。通过扫频的方法测量在不同的频率点下的幅值和相位变化。在工程应用中,只需要知道被测系统的相位变化在正常的范围内就可以视系统的动态性能正常。该仿真算法只是建立了一个模型。在实际运用时还需要变换测试信号的频率和周期。(A single frequency sinusoidal correlation method of testing dynamic testing system is simple, does not require system identification. Only need to observe the difference between the measured system output signal and amplitude change. Swept through the method of measurement points at different frequencies under the amplitude and phase changes. In engineering applications, only need to know the system under test changes in the normal phase it may be possible within the framework of the dynamic performance of the system to normal. The simulation algorithm is the establishment of a model. In the practical application of test signals also needed to change the frequency and periodicity.)
    2009-11-28 14:29:19下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载