-
Labview-ATM-Simulation
使用生产者与消费者模式模拟ATM机,可以实现存取款及余额查看功能(Using Labview to simulate ATM.)
- 2013-08-31 19:27:54下载
- 积分:1
-
Active-Noise-Control
用LabVIEW实现主动噪声控制多通道Fx-LMS算法,可以读取任意wav文件进行降噪处理并得到控制效果。(Active Noise Control with LabVIEW multichannel Fx-LMS algorithm, you can read any wav file for noise reduction and get control results.)
- 2020-09-10 16:38:01下载
- 积分:1
-
ang_continue_measure_ver2.0-
5124采集程序,频谱显示,时域波形显示,存储,通道之间的相位差计算(5124 collection procedures, spectrum display, time-domain waveform display, storage, compute the phase difference between channels)
- 2013-06-29 10:16:45下载
- 积分:1
-
key_led
用labview来实现矩阵按键和oled屏幕显示。。(Use labview to achieve matrix keys and oled screen display. )
- 2020-07-17 20:48:48下载
- 积分:1
-
TDMS-functional-VI
labview TDMS的各种高速存储功能,(LabVIEW TDMS a variety of high-speed storage function,)
- 2020-12-05 19:49:23下载
- 积分:1
-
ocean spectrometer
用于读取ocean光谱仪的光谱数据、保存光谱数据至tdms文件、并通过daq设备输出对应的模拟电压。
(需要安装ocean光谱仪驱动、daq-mx驱动)(Used to read spectral data of ocean spectrometer, save spectral data to TDMS file, and output corresponding analog voltage through DAQ device.)
- 2017-07-28 11:35:11下载
- 积分:1
-
直流电机转速控制.tar
说明: 基于转速环-电流环双闭环控制的直流电机调速系统的labview上位机程序。(The LabVIEW upper computer program of DC motor speed control system based on double closed-loop control of speed-loop and current-loop.)
- 2019-06-17 16:55:09下载
- 积分:1
-
Signal power spectrum based on FFT
通过labview 对信号进行分析,主要包括基于FFT求信号功率谱(The signal is analyzed by LabVIEW, mainly including the signal power spectrum based on FFT)
- 2017-12-22 11:25:53下载
- 积分:1
-
Time-domain-analysis-system
本系统可做自动控制原理中的时域分析仿真实验,系统特性如下:
1:可选择仿真系统为一阶、二阶、任意阶
2:可选择信号源为正弦波、三角波、锯齿波、方波(可模拟阶跃信号),并可调节信号源频率、幅值、相位、偏移、方波占空比
3:可选择信号采样率及采样数
4:自动计算传递函数
5:自动计算时域响应参数(增益系数、上升时间、峰值、峰值时间、稳定时间、超调量)
6:波形图同时显示原始信号和响应信号
注:使用本系统需安装labview控制设计与仿真库(The system can do automatic control theory in the time-domain analysis simulation, the system behaves as follows: 1: simulation system can be selected for the first, second, any order 2: select the signal source is a sine wave, triangle wave, sawtooth, square wave (analog step signal), and can adjust the signal source frequency, amplitude, phase, offset, duty cycle square wave 3: the the optional signal sampling rate and the number of samples 4: automatic calculation of the transfer function 5: Automatic calculation domain response parameters (gain coefficient, rise time, peak, peak time, settling time, overshoot) 6: waveform diagram shows both the original signal and the response signal Note: Use the system to be installed LabVIEW Control Design and Simulation library)
- 2013-05-12 11:53:34下载
- 积分:1
-
LabVIEW
基于labview的风电轴承故障检测与监测(Wind power bearing fault detection and monitoring based on labview)
- 2014-02-15 19:05:15下载
- 积分:1