登录
首页 » matlab » Endpoint-detection

Endpoint-detection

于 2014-04-04 发布 文件大小:3KB
0 185
下载积分: 1 下载次数: 30

代码说明:

  基于短时能量与过零率、倒谱特征和谱熵的三种语音端点检测(Endpoint detection)

文件列表:

新建 文本文档.txt,10403,2014-04-04

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • icaMF
    Independent Component Analysis源代码,最大似然方法(Independent Component Analysis source code, the maximum likelihood method)
    2007-07-30 10:21:48下载
    积分:1
  • allsv_pwm
    MATLAB FILES FOR INDUCTION MOTOR
    2015-03-28 15:50:51下载
    积分:1
  • Vector
    上电后,在BRAKE信号无效,且保护逻辑无输出的情况下? 电机按DIRECTION信号的方向转动? 电流传感放大器采样电机电枢电流,经13脚的RC网络转换为电压值,与D/A转换输出的预定阀值相比较。如果当前的电流使转换的电压值小于阀值?(Power after the BRAKE signal is invalid, and the protection logic no circumstances ? electrical output signals according to the direction of rotation DIRECTION ? current sensing amplifiers motor armature current sample by 13 feet of RC network is converted to voltage value, and D/A conversion output compared to the target threshold. If the current of current to voltage conversion value is less than threshold ?)
    2009-11-06 21:26:43下载
    积分:1
  • MGLab1.0
    说明:  多网格的源程序,希望对大家有帮助,好东西一起分享(Multi-grid source, we want to help, to share good things)
    2011-03-24 19:39:47下载
    积分:1
  • MIMO
    MIMO系统仿真 空时分组码 空分复用 BLAST结构(MIMO STBC system simulation MIMOs BLAST structure)
    2014-12-20 20:47:04下载
    积分:1
  • MATLAB-SIMULINK-Simulation
    《电力系统的MATLAB-SIMULINK仿真与应用》 王晶等编 2008年(Power system MATLAB-SIMULINK simulation and application Jing, eds 2008)
    2013-09-21 19:59:43下载
    积分:1
  • hengten_v88
    DC-DC部分采用定功率单环控制,计算晶粒的生长,入门级别程序,基于负熵最大的独立分量分析。( DC-DC power single-part set-loop control, Calculation of growth, entry-level program grains Based on negative entropy largest independent component analysis.)
    2016-12-04 18:52:55下载
    积分:1
  • 拉丁超立方 (2)
    说明:  假如数据中有N 个变量,而我们想抽取的样本的数量是M,那么在对数据进行抽样的时候,这种方法首先会把N个变量的设计空间均匀的划分开为M份,然后在每个划分好的区域中随机的抽取一点,最后,从这M个变量里,随机挑选之前选好的点,构成我们的样本(If there are n variables in the data, and the number of samples we want to extract is m, then when sampling the data, this method will first divide the design space of n variables into M parts evenly, and then randomly extract a point in each divided area. Finally, from the m variables, randomly select the previously selected points to form our sample)
    2021-04-07 19:47:52下载
    积分:1
  • QPSK-Modulation-and-Demodulation
    此例程为配套书籍的第六章例题7-19的相对应代码,功能为QPSK调制与解调,编程环境为matlab。(This routine supporting books Chapter Example 7-19 corresponding to the code for the function QPSK modulation and demodulation, programming environment Matlab.)
    2013-05-02 18:53:34下载
    积分:1
  • LLREXM
    LLR仿真 157循环编码 llr译码 BPSK信号高斯噪声(LLR 157 loop simulation BPSK signal decoding coded llr Gaussian noise)
    2013-05-26 10:27:17下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载