colorhistogram

Matlab中三相交-交变频器的仿真,利用SPWM调制实现开关管的动作(the simulantion model of three-phase ac-ac converter )

说明：  CONTENTS CHAPTER 2 (C2 Folder) INTRODUCTION TO MATLAB/SIMULINK Exercise 1: Variable Frequency Oscillator SIMULINK file s1.mdl MATLAB m-file m1.m Exercise 2: Parallel RLC Circuit SIMULINK file s2.mdl MATLAB m-file m2.m MATLAB m-file m2init.m(1st half of m2.m) MATLAB m-file m2plot.m(2nd half of m2.m) Exercise 3: AC Energization of a RL Circuit SIMULINK file s3.mdl MATLAB m-file m3.m Exercise 4: Series RLC Resonant Circuit SIMULINK file s4.mdl MATLAB m-file m4.m

流水线型车间作业调度问题可以描述如下：n个任务在流水线上进行m个阶段的加工，每一阶段至少有一台机器且至少有一个阶段存在多台机器，并且同一阶段上各机器的处理性能相同，在每一阶段各任务均要完成一道工序，各任务的每道工序可以在相应阶段上的任意一台机器上加工，已知任务各道工序的处理时间，要求确定所有任务的排序以及每一阶段上机器的分配情况，使得调度指标(一般求Makespan)最小。下面的源码是求解流水线型车间作业调度问题的遗传算法通用MATLAB源码，属于GreenSim团队原创作品，博客上发布的是不完全的源码，本人将其补充完成已成功运行，转载请注明GreenSim团队原创作品。(Pipelined job-shop scheduling problem can be described as follows: n tasks on the assembly line m processing stages, each stage has at least one machine and at least one stage there are multiple machines, and the same processing performance of each machine on the same stage , at every stage to complete each task are a process, each process of each task can be processed on any machine on the corresponding stage of the processing time of each process known tasks, all tasks required to determine the sort and every Distribution of the machine on a stage, making scheduling index (typically seek Makespan) Min. The following code is a Genetic Algorithm for Job Shop Scheduling Problem pipelined general MATLAB source code, original works belong GreenSim team, the blog post is incomplete source code, I will supplement has been successfully completed its operation, please indicate the original team GreenSim works.)

非线性支持向量机,在样本基础之上，进行预测分析。可应用于底板破坏深度计算。(Nonlinear support vector machine (SVM) )

频谱感知 能量检测算法 SNR -15 -20对比输出结果(energy detection spectrum sensing)

omnet环境下如何建立wsn节点并模拟仿真(omnet environment and how to establish wsn node simulation)

matlab书籍 希望对matlab学习的人有所帮助(matlab books want to learn matlab help)

Program for Linear block code

自学Matlab必备的60个小程序代码.(Self-study Matlab necessary 60 small code )

这类控制器在大偏差范围内利用模糊推理的方法调整系统的控制量U，而在小偏差范围内转换成PID控制，两者根据事先给定的偏差范围自动实现。(This kind of controller in the big deviation range by using fuzzy reasoning method to adjust the system control quantity U, and in small deviation range NaZhuan with PID control, both, according to a given skew range prior to implementation.)