登录
首页 » LabView » labview-codebox

labview-codebox

于 2012-12-25 发布 文件大小:26KB
0 269
下载积分: 1 下载次数: 7

代码说明:

  基于labview的简易密码器程序,密码输入错误提示,多次错误退出程序(A simple password box program based on labview , when enter the incorrect password, a error message would show to you,and the program will exit when entering the wrong password for three times.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 3
    说明:  labview很重要的例程,适用于labview新手(it is very important for the new student of labview ,very usful)
    2017-07-26 15:40:04下载
    积分:1
  • fangbobaizaosheng
    用Labview仿真出一个加有均匀白噪声的仿真信号,并显示出波形(Using Labview simulation of a uniform white noise plus a simulated signal and displays the waveform)
    2020-11-12 16:09:44下载
    积分:1
  • USB-bluetooth-configuration
    USB配置蓝牙模块。实现功能:配置蓝牙模块。再读取蓝牙模块数据程序。此代码为我毕业设计,现与大家分享!!!(USB bluetooth configuration software. configuration buletooth module。)
    2012-05-15 11:52:25下载
    积分:1
  • Thermometer
    labview大学教程书籍例程。温度计前面板,包含输入和显示控件。(labview university course books routines. Thermometer front panel contains the input and display controls.)
    2013-07-05 20:50:08下载
    积分:1
  • Labview-Data-Grid-View
    1.基于Labview的DataGridView应用例程; 2.可用作优化界面风格; 3.对表格的操作更强大;(1.It is base on labview example of Data Grid View 2.It can be used to optimize the interface 3.It has the strong ability of operating the table.)
    2021-01-29 00:18:35下载
    积分:1
  • LABVIEW_TONGBU
    LABVIEW prepared by the NI timing synchronization control card, control the camera synchronized shooting
    2016-12-27 12:52:15下载
    积分:1
  • Write-Parameter-to-PLC
    基于labview建立与PLC的通讯,并进行参数的写入(Labview establish communication with the PLC and write parameters based)
    2020-06-26 22:40:01下载
    积分:1
  • hanshuxinhaofashengqi
    1.采用Labview设计一虚拟函数信号发生器, 通过数据采集卡输出波形信号,调节信号的相关参数,可观察示波器上波形的变化情况。 ⑴ 以NI MyDAQ数据采集卡作为输出接口; ⑵ 数据采集卡输出多种信号,至少完成三种波形:正弦波、三角波、方波(可调占空比)的输出,同时前面板上显示各输出波形; ⑶ 频率、幅值、初相位、直流偏移量和方波的占空比(0~100 )等参数可以通过前面板控件调节。 ⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes. ⑴ with NI MyDAQ data acquisition card as output interface ⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel ⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust. ⑷ output waveform can be displayed on the front panel.)
    2015-04-25 18:26:52下载
    积分:1
  • SNAKE
    LABVIEW贪吃蛇案例程序,希望能有用!(Snake Case LABVIEW program, hoping to be useful!)
    2014-01-05 18:59:36下载
    积分:1
  • Wavelet analysis
    程序实现对信号的小波分析以及频谱分析,具有美观的界面和数据存储功能。(The program realizes wavelet analysis and spectrum analysis of signals, and has beautiful interface and data storage function.)
    2020-07-24 16:08:43下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载