x86_processor_asm123321

电动车从起跑线出发（车体不得超过起跑线），沿引导线到达B点。在“直道区”铺设的白纸下沿引导线埋有1~3块宽度为15cm、长度不等的薄铁片。电动车检测到薄铁片时需立即发出声光指示信息，并实时存储、显示在“直道区”检测到的薄铁片数目。 （2）电动车到达B点以后进入“弯道区”，沿圆弧引导线到达C点（也可脱离圆弧引导线到达C点）。C点下埋有边长为15cm的正方形薄铁片，要求电动车到达C点检测到薄铁片后在C点处停车5秒，停车期间发出断续的声光信息。 （3）电动车在光源的引导下，通过障碍区进入停车区并到达车库。电动车必须在两个障碍物之间通过且不得与其接触。 （4）电动车完成上述任务后应立即停车，但全程行驶时间不能大于90秒，行驶时间达到90秒时必须立即自动停车。 -err

DS1302的驱动程序，C51编的，最后由proteus仿真的，可以显示设定时间，程序中的延时函数是由汇编语言实现，也就是说这程序是C和汇编混编的。-DS1302 driver, C51 series, and finally by the Proteus simulation can show the set time delay proceedings by the assembly language function is to achieve, that is to say that the procedure is of mixed C and assembler.

该文件的内容是设计一个五层楼的电梯控制装置,要求每层楼根据需要控制设上下控制按键及按键指示灯,全部楼层只设置一个当前楼层显示 电梯内设开关门按键 各楼层按键及指示灯,开关门要有声响提示 每层楼高度为0.30米,楼层全高1.5米-the contents of this document is to design a five-storey building in the lift control device on each floor under the requirements necessary to control the upper and lower control buttons located buttons and lights, all floors can provide a current show floor elevator door keys internal switches on each floor of buttons and lights, switches doors have audible alert signal height of each floor 0.30 meters, the entire floor 1.5 meters high

说明：  基阵信号处理，此程序为线阵面阵圆阵的方向图。(Array signal processing, linear array circular array pattern.)

《汇编语言》(Assembly Language)是计算机专业中一门重要的基础课程，是一种面向机器的低级语言。它依赖于硬件，能通过巧妙的程序设计充分发挥硬件的潜力。汇编语言程序产生的代码运行效率高。因此，到目前为止，许多软件系统(例如操作系统等)的核心部分仍然用汇编语言来编写。-err

用汇编语言编写的简短小巧的记事本程序-assembler language short compact notebook procedures

录音机控制51源程序-recorders source control 51

在基于脉冲的UWB系统中，采用瑞克接收机合并多径信号能量并进行相干检测，信道估计问题即估计多径信号的到达时间和幅度。在基于OFDM的UWB系统中，接收机根据信道频域响应对每个子信道进行频域均衡后进行相干检测，信道估计问题即估计信道频域响应。-Pulse-based UWB systems, rake receivers using the combined multipath signal energy and coherent detection, channel estimation problem that is estimated multipath signal arrival time and amplitude. OFDM-based UWB system, the receiver under the channel frequency response of each subchannel to frequency domain equalization after coherent detection, channel estimation problem that is estimated channel frequency response.

用51汇编编写的CRC-4校验程序,生成多项式g(x) = x4 + x + 1, 非常适合数据量不大的场合.-51 compilation prepared by CRC-4 checksum procedure to generate the polynomial g (x) = x4+ X+ 1, the amount of data is not very suitable for the occasion.

利用ds18b20对外界的温度进行采集,利用led进行温度的实时显示-The use of the temperature of the outside world ds18b20 collection led to the use of real-time display of temperature