MFGTI

Intel196kc自动化保护用的测控主机板用源代码程序。包括初始化，运行，调试，通信，代用傅里叶技术计算等自动化技术。液晶链接部分(Intel196kc automation protection for the control host board using the source code program. Including initialization, operation, debugging, communication, and substitution of Fourier technology and other automation techniques)

Keil C uVision4 集成开发环境详细中文教程，对于新使用Keil C uVision4 很好的资料。(Keil C uVision4 detailed Chinese tutorial integrated development environment, for a new use Keil C uVision4 good information.)

说明：  光伏发电系统三相逆变并网及其仿真研究，论文详解。(Study on three-phase inverter Grid connection and its simulation of photovoltaic power generation system)

STM32F407信号发生器输入一个正弦波，AD采样，DA输出，系统频率应该是输入的波形的频率的10倍以上保证输出波形的完整性，系统的输出频率可以使用示波器测试出。(Stm32f407 signal generator input a sine wave, AD sampling, Da output and system frequency should is 10 times the frequency of the input waveform to guarantee that the above output waveform of integrity, the output frequency of the system can use oscilloscope to test out. )

PIC12F675 GP3使用方法程序 加protues 仿真 (PIC12F675 GP3 plus protues simulation using the methods and procedures)

SiRF Binary Protocol Reference Manual Rev2.3-Dec07

基于MLX90614的公共场所体温快速检测器的设计(......delay.asm ......hex2asc.asm ......Init.asm ......main.asm ......main.COD ......main.err ......main.HEX)

TM4C123系列芯片读取DS18B20的数值并通过串口发送数据。(TM4C123 tiva ware micro-controller reads DS18B20 value and sends it through UART)

这是一个在万能充电器中能自动识别电池极性的电路图，非常巧妙的设计(This is a universal battery charger can automatically identify the polarity of the circuit, very clever design)

1.由上位机发送1给单片机时，蜂鸣器以400ms频率发声，发2时以200ms频率发声，发3时以100ms频率发声，发4时关闲蜂鸣器。 1.以2400bps从计算机发送任一字节数据，当单片机收到该数据后，在此数据前加上一序号然后连同此数据一起发送至计算机，当序号超过255时归零。 2.以16进制发送一个0-65536之间的任一数，当单片机收到后在数码管上动态显示出来，波特率自定。 3. 用AD以1HZ的频率采集模拟信号，然后转换成数字量，再将其以1200bps发送到计算机，在计算机上显示。 4.按下矩阵键盘第一行时以1200bps发送，1，2，3，4，第二行时以2400bps发送5，6，7，8，第三行以4800bps发送，9，10，11，12，第四行以9600pbs 发送，13，14，15，16. (1. From the PC to send a single chip, the buzzer to 400ms frequency of sound, made 2 to 200ms frequency sound, made from 3 to 100ms frequency sound, made 4 free buzzer off. 1. To 2400bps from the computer to send any byte of data, when the microcontroller receives the data in this data with a serial number before then sent along with the data to the computer, the serial numbers when more than 255 zero. 2. To send a 16-hexadecimal any number between 0-65536, when the microcontroller in the digital receipt is displayed on a dynamic, custom baud rate. 3. 1HZ with the frequency of AD in order to capture analog signals, then converted to digital, and then send it to 1200bps to the computer, the computer display. 4. Press to 1200bps matrix keyboard to send the first row, 1,2,3,4, 5,6,7,8 the second row to 2400bps send the third line to 4800bps send, 9,10,11,12 , the fourth line to 9600pbs send, 13,14,15,16. )