BLDC

基于matlab的AZSPWM模型，降低共模电压(Matlab-based AZSPWM model, reduce the common mode voltage)

广义球形解码源代码，包括信噪比、复杂度、以及天线数量各种参数的仿真(Generalized sphere decoder source code, including signal to noise ratio, complexity, and various parameters of the simulation the number of antennas)

dsp bridge for dsp arm embedded systems

说明：  3DMM模型是三维人脸重建的基础模型，用于三维人脸重建任务。(3dmm model is the basic model of 3D face reconstruction, which is used for 3D face reconstruction task.)

用interrupt控制两个电机，要求可以随意改变任意一个的速度(use interrupt)

子载波功率资源分配，OFDM技术将信道分成许多正交子信道，在每个子信道上使用一个子载波进行调制，并且各个子载波并行传输(Power resource allocation of the sub-carriers, OFDM technology will channel into a number of orthogonal subchannels, in each subchannel to use a sub-carrier modulation, and the respective sub-carrier parallel transmission.)

PSO训练BP网络的matlab代码，下载后，加入输入输出样本即可运行。(PSO trained BP network matlab code, download, add input and output samples can be run.)

1．EMIF 接口 TMS320F28335DSP 的扩展存储器接口(EMIF)用来与大多数外围设备进行连接，典型应用 如 连接片外扩展存储器等。这一接口提供地址连线、数据连线和一组控制线。ICETEK–F28335-A 将这些扩展线引到了板上的扩展插座上供扩展使用。 2．液晶显示模块的访问、控制是由28335ADSP 对扩展接口的操作完成。 控制口的寻址：命令控制接口的地址为 0x208001，数据控制接口的地址为0x208003 和 0x208004，辅助控制接口的地址为0x208002。 3．显示控制方法： -液晶显示模块中有两片显示缓冲存储器，分别对应屏幕显示的象素，向其中写入数值将改 变显示，写入“1”则显示一点，写入“0”则不显示。(The 1.EMIF interface Extended TMS320F28335DSP memory interface (EMIF) is used to connect with the most peripheral equipment, typical application Such as The connecting piece of extended memory. This interface provides the address lines, data lines and a set of control line. ICETEK- F28335-A The extension line to the extension socket for plate on the expansion of the use of. 2 liquid crystal display module access, control by the 28335ADSP to the extended interface operation is complete. Addressing control port: Command and control interface address 0x208001, the address data control interface for 0x208003 and 0x208004, auxiliary control interface address for 0x208002. 3 display control method: - liquid crystal display module with two display buffer memory, respectively corresponding screen pixel, writing values will be changed to the Change display, write "1" shows a little, write "0" are not displayed.)

DC-DC变换器的DSP28335控制程序，采样TI的软件架构，实现软启动，闭环控制等(DC-DC converter DSP28335 control procedures, sampling TI software architecture, soft start, closed-loop control)

说明：  遗传算法程序是在 MATLAB环境下仿真的程序。可以在任何版本用的(genetic algorithm in MATLAB environment simulation procedures. In any version of)