-
MPU-6050资料
三轴陀螺仪三轴加速度计的驱动代码,可有用来计算物体的运动状态。(Three-axis gyroscope three-axis accelerometer driver code.)
- 2017-12-28 10:39:48下载
- 积分:1
-
5702_PWM_移动电源
松翰SN8F5702_PWM_移动电源方案(Songhan SN8F5702_PWM_Mobile Power Supply Scheme)
- 2020-06-17 04:00:01下载
- 积分:1
-
div7
Director.lua used for corona sdk programming nothing more bullshit i just need to download a project in here and i dont have any money to avail that VIP so im gonna use the uploading fucking shit. no more worries fuckers.
- 2014-02-14 00:33:35下载
- 积分:1
-
84-15W4K-6路PWM
拾球小车,遥控小车PWM调速,4舵机4麦克纳姆轮,HC06与手机遥控(Pick up the ball car, remote control car PWM speed regulation, 4 steering gear 4 McNam wheel, HC06 and mobile phone remote control)
- 2020-06-17 20:40:04下载
- 积分:1
-
Steering_Engine
在arduino平台上,利用数字通信口输出pwm信号从而控制舵机转角(On the arduino plate, to use pwm signal control the rotation angle of steering engine.)
- 2021-03-22 14:39:16下载
- 积分:1
-
PID算法原理
详细介绍PID控制原理,展示了PID控制器的控制表达式。(The PID control principle is introduced in detail, and the control expression of the PID controller is shown.)
- 2018-11-19 19:48:27下载
- 积分:1
-
dianzhen
点阵原理图,595和138,没错这就是电路板
·OLED例程,适合12864,具体使用请根
·台达PLC Modbus协议通信dll com控件
·单片机红外遥控最全的资料,包含很
·非接触式IC卡开发板源程序,包括原
·C51实用程序(45个) I/O、定时( OLED routines, suitable for 12864, please use the specific root
· Delta PLC Modbus protocol communication dll com Controls
· Infrared remote control MCU most complete information, including the very
· Non-contact IC card development board source, including the original
· C51 utility (45) I/O, timer)
- 2013-08-24 18:02:56下载
- 积分:1
-
PLCPROFIBUSFANUC
这是我自己原创的关于西门子PLC 与FANUC机器人之间的PROFIBUS通信方式。任何部分皆为第一次上传到网上。(all the file are make by my self,thankyou!)
- 2021-02-22 09:29:42下载
- 积分:1
-
MCB_SOR_1.0
固高运动控制卡源代码,内容详细,对入门运动控制的朋友非常有用。(gugao motion control card system source code, detailed content on the entry of the control of the movement of a friend is very helpful)
- 2020-09-10 21:28:02下载
- 积分:1
-
labview-danpianji
利用Keil C51 和LabVIEW编写程序实现PC与单片机串口通信。
设计任务
PC通过串行口将数字(00 ,01 ,02,03... ,FF,十六进制)发送给单片机,单片机收到
后回传这个数字,PC接收到回传数据后显示出来,若发送的数据和接收到的数据相等,则串
行通信正确,否则有错误。启始符是数字00,结束符是数字 FF。(Use Keil C51 and LabVIEW programming to achieve PC serial communication with microcontroller. Displayed after the PC via the serial port design task digital (00, 01, 02,03 ..., FF, hex) is sent to the microcontroller, the microcontroller receives return this figure, PC receives the return data , if the data sent and received data are equal, the serial communication is correct, otherwise an error. Startup character is a number 00, the end of the character is a number FF.)
- 2020-07-01 04:20:01下载
- 积分:1