-
matlab-PID-
用matlab实现了PID 控制的编程,得到了较好的控制效果(Realize a PID control with matlab programming, get a better control effect)
- 2011-11-22 15:53:43下载
- 积分:1
-
dingbuchangLMS
最新的定步长LMS自适应滤波算法,对自适应算法有很大帮助(The latest fixed step size LMS adaptive filtering algorithm)
- 2015-01-12 12:39:18下载
- 积分:1
-
matlabfozzee
基于matlab的模糊神经网络仿真源程序(Matlab-based fuzzy neural network simulation source)
- 2008-05-04 15:54:11下载
- 积分:1
-
matlabinter
说明: AVS帧内预测算法的MATLAB代码,具体做了水平预测、垂直预测、DC和左上预测、右下预测。(AVS intra-prediction algorithm MATLAB code, the specific level of the forecast done, vertical prediction, DC prediction and the upper left, lower right forecast.)
- 2008-10-23 14:28:11下载
- 积分:1
-
MATLAB-gui-voice-
说明: 关于matlab方面对语音进行信号处理方面的内容(Matlab voice on the terms of the content of the signal processing)
- 2011-04-10 14:11:41下载
- 积分:1
-
CRC.Press.MatLab.Primer.Seventh.Edition
A very popular book on MATLAB
- 2011-05-31 04:38:41下载
- 积分:1
-
fractal-image-compression-using-Quadtree-decompos
MAtlab code for fractal image compression
- 2014-12-20 21:25:46下载
- 积分:1
-
ejemploPCA
Algorith PCA in Matlab. The example is basic, with random data
- 2010-01-19 10:32:43下载
- 积分:1
-
PCNN---2D-OTSU
给出了基于2D-OTSU算法的PCNN自动循环迭代源代码,用于图像分割,效果良好。(PCNN code for image segmentation based on 2D-OTSU)
- 2010-05-14 20:46:02下载
- 积分:1
-
项目4
说明: 任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。
要求:
1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。
2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。
3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify.
Requirement:
1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km.
2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm.
3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
- 2019-05-13 09:39:41下载
- 积分:1