M2IDE_V138

利用MSP430单片机实现5分钟倒计时。用Timer_A实现1s定时，4位共阳型数码管显示时间，显示格式为：“x-xx”，分别代表“分”、“十秒”和“秒”。每隔1s，倒计时器的时间减1，倒计时从4分59秒开始计时，至0分0秒结束，停止计时。(MSP430 microcontroller is used to realize 5 minute countdown. Timer_A is used to realize 1s timing and 4-bit common-sun digital tube display time. The display format is "x-x x", representing "minutes", "ten seconds" and "seconds" respectively. Every 1s, the countdown time is reduced by 1. The countdown time starts at 4:59 seconds and ends at 0:0 seconds.)

说明：  采用STC15W402单片机控制的电路及源程序，已批量生产；(The circuit and source program controlled by stc15w402 single chip microcomputer have been mass produced;)

说明：  四个舵机的键盘输入控制，需要使用arduino的串口通讯和串口监视(Keyboard input control of the four steering engines requires the use of arduino serial port communication and serial port monitoring)

使用stm32的串口实现fifo队列缓冲读写数据，值得新手学习(Using STM32 serial port to realize FIFO queue buffer read and write data, it is worth learning by novice.)

说明：  主要实现了STM32F10X的串口dma，实现了flash操作；并且 直接可以编译运行;(It mainly implements the serial port DMA of STM32F10X, realizes flash operation, and compiles and runs directly.)

瑞萨单片机rl78 iic程序 官方源码 亲测 能用(Renesas MCU rl78 iic official source program   Pro-test can)

用于可见光通信的发射和接受端的程序，使用曼彻斯特编码(Program for transmitting and receiving ends for visible light communication, using Manchester coding)

ssd1289-3.2的基于STM32的测试程序。(ssd1289-3.2 testing procedures based on the STM32 )

STM32 SPI读写FM25CL64铁电存储器，程序为103RBT6单片机读写代码，包括SPI初始化、字节发送接收代码、FM25CL64读写代码(STM32 SPI read/write FM25CL64 ferroelectric memory, the application for 103 rbt6 microcontroller, speaking, reading and writing code, including the SPI initialization code byte code to send and receive FM25CL64, speaking, reading and writing )

汽车信号灯控制系统的设计 汽车上的信号灯有:转向灯(左前灯、右前灯、左后灯、右后灯，仪表盘上的二 个指 示灯 )及夜间示 宽灯等 。 当汽车转 弯 、刺 车 停 靠时 ，转 向灯 发出不同 的信号 ；夜问 ．则 点 亮示宽 灯。汽 车转弯或停 靠时 ，相应的 信号灯要 发出 闪烁 的灯光 信号 ， 目前 国内广泛 缱 用 电热 式闪光 器产生 闪光信 号 。(Auto Light Control System lights on the car include: turn signal (front left light, right front lamp, left rear lamp, right rear lights, two lights on the instrument panel) and night lights, wide display. When the car turn, stop puncture car, the turn signal send mixed signals nighttime. The width light is lit. Car turns or stops, the corresponding signal to a flashing light signal, the current domestic-type electric flash wide loving generated by the flash signal.)