OFDM-QAM16

QPSK的编译 设定噪声为高斯白噪声，对2ASK、2FSK、2PSK、2DPSK等各种调制方式及相应的主要解调方式下（分相干与非相干）的误码率进行统计，并与理论值进行比较，以图形方式表示误码率与信噪比间的关系。(QPSK compiled Set the noise is Gaussian white noise, right 2ASK, 2FSK, 2PSK, 2DPSK variety of modulation and demodulation mode corresponding to the main (sub-coherent and non-coherent) error rate statistics, and with the theoretical value comparison, a graphical representation of bit error rate and SNR relationships.)

通过matlab实现车联网下的资源分配，包括用户、路边单元和基站，相关毕设可以使用(Matlab is used to realize the resource allocation under the vehicle network, including users, roadside units and base stations, which can be used in relevant settings.)

Selective mapping algorithm is proposed to reduce the peak-to-average power ration (PAPR) in MIMO-OFDM system. It is proved that the conjugate symbols on two antennas have the same PAPR property with orthogonal space-time block coded (STBC). By using the characteristic, the computational complexity cost and the side information (SI) is significantly reduced compared with the concurrent SLM algorithm. Simulation results demonstrate that the performance of the proposed algorithm outperforms the conventional concurrent SLM algorithm.

1）设计Butterworth型音频抗混叠滤波器； 2）参数： 下通带频率300Hz；上通带频率3400Hz； 下阻带频率280Hz；上阻带频率3600Hz； 通带最大衰减0.3dB； 阻带最小衰减40dB； 3）采用一低通滤波器和一高通滤波器级联； 4）分别确定LPF和HPF的性能指标； 5）求出两滤波器的系统函数和频率响应，并画出其幅频特性曲线； 6）求整个滤波器的系统函数和频率响应，并画出其幅频特性曲线。(1) the design of Butterworth-type audio anti-aliasing filter 2) parameters: passband frequency of 300Hz on pass-band frequency 3400Hz under the stop-band frequency of 280Hz on stop-band frequency 3600Hz passband maximum attenuation of 0.3dB minimum stopband attenuation of 40dB 3) the use of a low-pass filter and a high-pass filter cascade 4) separately to determine the performance of LPF and HPF target 5) to derive two-filter system function and frequency response, and draw its increase frequency characteristic curve 6) for the entire filter system function and frequency response, and draw its amplitude-frequency characteristic curve.)

LDPC性能仿真(LDPC performance simulation)

LTE系统中信道的加扰调制部分,子载波建立的必要过程( LTE, modulate ,scrambing,16QAM,64QAM,QPSK,)

调试串口很有帮助，用windowsAPI编写，避免了com控件的局限性(help for serialport debug)

说明：  2. 关于无线信道的多普勒谱，请回答以下问题： (1) 在某些无线信道中，多普勒频移会引起无线信道输出信号的混叠。请描述产生混叠的各种原因； (2) 无线信道中的多普勒谱有一种经典谱(classic spectrum)，请解释产生这种谱形状的机理； (3) 请用Simulink工具编写代码(S-Function方式)，产生一单径瑞利信道，其多普勒谱为经典谱，其中移动速率为120km/h。并请回答：证明自己用计算机产生的经典谱是正确的可能方法。 (On the wireless channel of the Doppler spectrum, please answer the following questions: (1) In some radio channels, the Doppler frequency shift will cause the output signal of the wireless channel aliasing. Please describe the aliasing produced a variety of reasons (2) wireless channel in the Doppler spectrum has a classical spectrum (classic spectrum), please explain the mechanism of produce such spectral shape (3), please use the Simulink tool to write code ( S-Function mode), resulting in a single-path Rayleigh channel, the Doppler spectrum for the classical spectrum, including mobile rate of 120km/h. And requested the answer: that they used computer-generated classical spectrum is the right possible way.)

simulink for BPSK modulation

一系列包含串口、Modem、收发传真、终端仿真等方面的编程例子( A series of contains aspect the and so on string mouth, Modem, receiving and dispatching facsimile, terminal simulation programming example )