-
amanatide1212
A fast and simple voxel traversal algorithm through a 3D space partition (uniform grid)
- 2010-11-11 08:34:13下载
- 积分:1
-
example_4_a
FDTD 集总参数原件的更新方程基本代码,,集总参数电路,电源。电压,电阻等建模(FDTD lumped parameter element update equation basic code)
- 2017-04-07 19:23:20下载
- 积分:1
-
SpatialMultiplexing_OpenLoop_Mode3
LTE下行链路空分复用开环。仿真配置:16QAM调制、1/3码率Turbo编码、10MHz带宽、每个子帧一个PDCCH符号、单码字,8次迭代Turbo译码、早期终止机制、MMSE(最小均方误差)MIMO接收器,PDSCH发射端进行空分复用预编码。信道模型是LTE-MIMO信道附加AWGN信道。(LTE downlink space division multiplexing ring opening. Simulation Configuration: 16QAM modulation, 1/3 rate Turbo code, 10MHz of bandwidth, one PDCCH per subframe symbol, single code word, 8 Turbo decoding iterations, early termination mechanisms, the MMSE (minimum mean square error) the MIMO receivers, PDSCH transmitting terminal space division multiplexing precoding. Channel model is LTE-MIMO channel additional AWGN.)
- 2016-12-10 00:46:23下载
- 积分:1
-
robot_adaptive_control
说明: 本程序是机械手的自适应控制的仿真实例,m文件里有程序说明。(This procedure is the adaptive control of the manipulator simulation example, there is a program in the M file.)
- 2020-06-17 15:34:10下载
- 积分:1
-
MPPT
program simlink for tracking the maximum power point of the speed
- 2011-12-13 02:51:02下载
- 积分:1
-
whole-modle_entire
这个程序是关于汽车整车模型的分析,主要是垂向加速度和侧倾角速度的分析。(This program is the analysis of the automobile model analysis of the vertical acceleration and the roll angular velocity.)
- 2012-02-18 16:18:28下载
- 积分:1
-
Tsai
原始tsai算法的MATLAB文件,不含任何修改和优化成分,适合原始数据分析(Tsai MATLAB file the original algorithm, without any modification and optimization components for raw data analysis)
- 2010-07-11 19:03:29下载
- 积分:1
-
Color-Reproduction-from-Noisy-CFA-Data-of-Single-
Color Reproduction from Noisy CFA Data of Single Sensor Digital Cameras
- 2013-03-11 23:43:21下载
- 积分:1
-
code
MATLAB优化算法和案例应用,模糊逼近算法、模糊RBF网络、基于FCEM的TRIZ评价(MATLAB optimization algorithm and a case application, fuzzy approximation algorithm, fuzzy RBF network, TRIZ uation based on FCEM)
- 2015-03-30 14:53:39下载
- 积分:1
-
gramschmidtyuhouseholderhujian
fenbushuju文件用于拟合zernike波面与原始波面的偏差。clgs,mgs,get-CG-decomp文件分别为使用传统Gram-Schmit和修正Gram-Schmit算法实现QR分解,并获得计算值。而stability文件为Householder分解方法。工程上用来检验Gram-Schm的计算正确与否(fenbushuju file is used to fit zernike wave-front with the original wave-front deviations. clgs, mgs, get-CG-decomp files are for the use of the traditional Gram-Schmit and amendment of Gram-Schmit algorithm QR decomposition, and obtain the calculated value. The stability documents Householder decomposition. Engineering Gram-Schm used to test the correctness of the calculation of)
- 2020-11-02 10:39:53下载
- 积分:1