登录
首页 » matlab » pmsgjg

pmsgjg

于 2014-01-29 发布 文件大小:11KB
0 236
下载积分: 1 下载次数: 10

代码说明:

  采用matlab对平面四杆机构进行运动分析,并输出图像.(Using MATLAB to analyse the motion of planar four bar mechanism, and the output image)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • oqpsk1001
    软判决在OQPSK解调中实现对信号纠错的分析与纠错的(Soft-decision in the OQPSK demodulator to achieve error correction signal analysis and error correction)
    2008-12-17 20:35:11下载
    积分:1
  • voicebox
    voice box 语音识别箱 包含各种常用的语音处理程序(voice box voice recognition box)
    2013-03-19 08:59:41下载
    积分:1
  • dualloopinverterparallel
    一种用于无互连线逆变器并联的多环控制方法 针对传统逆变器无线并联系统稳态均流精度低和动态响应差等缺点,提出基于传统无 线并联下垂法的新型多环控制结构,分析了逆变器并联系统有功和无功功率的环流模型。( In this paper, a novel control scheme is presented, which is able to improve the transient response and power sharing accuracy of parallel-connected inverters with no control interconnections, and the active and reactive circulating current of the parallel system model are analyzed. A multiple-loop controller is developed based on the traditional droop method. )
    2012-10-11 16:51:47下载
    积分:1
  • fourfoot_robot_opt
    四足机器人的步态轨迹优化源码,运行main函数即可。(Four-legged robot s gait trajectory optimization code, you can run the main.m function)
    2011-12-19 00:16:54下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • Decode
    This program : use to calculate the tomographic slices, we needed to take a column from each projection and group them all together. The following sinogram is a collection of all the 64th columns from all of the projections the columns are then rotated to be horizontal.
    2013-04-14 16:53:02下载
    积分:1
  • work
    关于自动控制原理的一些matlab代码,帮助大家理解和学习matlab(About automatic control theory of some matlab code)
    2014-08-20 14:40:03下载
    积分:1
  • chap2
    《matlab应用大全》赵海滨编著,清华大学出版社,第二章主讲matlab科学计算,包括多项式的求值、插值、函数的极限算法(The application of matlab Zhao Haibin compiled, tsinghua university press, chapter 2 on matlab scientific computing, including evalu)
    2013-10-31 09:30:59下载
    积分:1
  • Matlab-symbolic-toolkit-introduction
    matlab 工具箱介绍_各函数及算法介绍(matlab toolbox functions and algorithms described _ Introduction of)
    2011-12-01 18:17:57下载
    积分:1
  • Signal_Generator
    说明:  基于PRBS码型产生QPSK和16QAM信号(QPSK and 16QAM signal generation based on PRBS code)
    2020-06-18 01:40:01下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载