登录
首页 » matlab » PSOR4

PSOR4

于 2012-01-19 发布 文件大小:2KB
0 275
下载积分: 1 下载次数: 11

代码说明:

  ANN using PSO coding

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • watrmak
    source code for watermark
    2010-03-09 21:38:48下载
    积分:1
  • 11
    说明:   该电路由一片四双向模拟开关集成电路CD4066为核心构成。每个电路内部有四个独立的能控制数字或模拟信号传送的开关。当水箱无水时,由于180K电阻的作用,使四个开关的控制端为低电平,开关断开,LED 不发光。随着水位的增加, 由于水的导电特性,使得IC的13脚为高电平,S1接通,LED1点亮。当水位逐渐增加时,LED依次发光指示水位。水满时, LED4发光, 显示水满。同时T1导通, B发出报警声,提示水已满。不需要报警声时,断开开关K即可。 (The circuit consists of a four-way analog switch integrated circuit CD4066 core composition. Within each circuit to control four separate digital or analog signal transmission in the switch. When the tank water, the role of the 180K resistor, so that the four low-side switch control, switch off, LED does not light. As the water level increases, the electrical properties of water, making the IC' s 13 feet high, S1 connected to, LED1 lights up. When the water level gradually increased, LED turn light level indication. Is full of water, LED4 LED display full of water. At the same time conducting T1, B alarm will sound, indicating that the water is full. Do not need to sound the alarm when the disconnect switch K can be.)
    2011-03-11 11:41:51下载
    积分:1
  • ixneighbors
    ixneighbors returns the indices of neighbor cells in a n*m matrix A. ic and icd are column vectors of same length where ic are the indices of cells in A and icd are the indices of the neighbor cells.
    2014-09-23 20:27:17下载
    积分:1
  • untitled
    matlab file newly created
    2011-10-27 01:24:09下载
    积分:1
  • Sliding-Mode-Control-Simulation
    滑模变结构控制MATLAB仿真(刘金锟) 的源程序 matlab(Sliding Mode Control MATLAB simulation (Liu Kun) source matlab)
    2015-08-05 12:17:44下载
    积分:1
  • dianliuzhihuanbijiaofa
    在电机调速应用中设计的三相电流滞环比较法(Motor speed control applications in the design of the current hysteresis in comparison )
    2010-11-20 15:54:13下载
    积分:1
  • chap4
    被控对象为G(S)=400/(s*s+500s),首先运行模糊控制器程序chap4_2.m,并将模糊推理系统保存在a2中,然后运行模糊控制SIMULIK程序。位置指令为0.5sin(10t),simulink见chap4_3(Controlled object is G (S) = 400/(s* s+500s), first run the fuzzy controller program chap4_2.m, and stored in a2 fuzzy inference system, and then run the fuzzy control SIMULIK program. Position command is 0.5sin (10t), simulink see chap4_3)
    2013-07-22 21:28:56下载
    积分:1
  • Blob-Code
    多种模式识别算法的编程实现,非常详细,包括PCA,MPCA,LLE等(Several pattern recognition algorithm is introduced, including PCA, MPCA, LLE etc.)
    2013-10-14 17:12:42下载
    积分:1
  • st
    说明:  S变换的源代码,实现对各种信号的频谱分析。该方法优越于短时傅里叶变换。(S transform source code, and the analysis of the spectrum of various signals. This method is superior to the short time Fourier transform.)
    2013-03-19 19:05:26下载
    积分:1
  • 20130422
    matlab毕业设计的一个小程序 我非常需要用用你们网站上的资料但是不知道怎么弄 我就在试试的,(Matlab graduate design a small program I really need to use on your site, but do not know how to get me to try,)
    2013-04-24 13:43:54下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载