-
plotp
plotting planes for matlab
- 2009-11-01 09:13:36下载
- 积分:1
-
simulatedannealing
数学建模美赛德经典算法MATLAB 源码之退火算法(MCM s very important algorithm simulated annealing)
- 2010-02-10 13:08:59下载
- 积分:1
-
OFDM3
ofdm三个信道的matlab仿真代码,功能强大,能显示各个部分功能,有误码率(three-channel ofdm matlab simulation code, powerful, and can display various parts function, bit error rate)
- 2011-06-01 13:18:35下载
- 积分:1
-
UPF_CSLU_talk
讲UPF的一个PPT,只对一篇经典文章的总结,我觉得很好,比看文章更能抓住重点.(UPF speaking of a PPT, is only a summary of the classic article, I feel good, better than to see the article focused.)
- 2009-09-11 16:32:11下载
- 积分:1
-
FDEfrequencyequalizer
根据LTE上行SIMO接收机特点,对MMSERISIC均衡器进行简化修改,得到MMSEFDE均衡器,该均衡器所有步骤全在频域进行,大大降低了均衡算法的复杂度。(LTE uplink SIMO receiver according to the characteristics of the MMSE-RISIC equalizer to simplify modification, by MMSE-FDE equalizer, the equalizer all the steps in full in the frequency domain, greatly reduces the complexity of balancing algorithm.)
- 2010-08-11 22:50:44下载
- 积分:1
-
walet
音频信号的小波分解与重构实例,在MATLAB里调用sym1小波函数进行三层分解。(audio signal decomposition and reconstruction by means of wavelet )
- 2012-04-14 10:31:17下载
- 积分:1
-
main1
AN EXCELLENT OUTPUT ORIENTED DESIGN OF BRUSHLESS DC MOTORS
- 2010-05-27 01:36:37下载
- 积分:1
-
Seismic_phase_rotation
This is the program to do the phase rotation in matlab for seismic data
- 2014-11-22 12:05:12下载
- 积分:1
-
潮流计算程序1
说明: 潮流计算是电力学名词,指在给定电力系统网络拓扑、元件参数和发电、负荷参量条件下,计算有功功率、无功功率及电压在电力网中的分布。潮流计算是根据给定的电网结构、参数和发电机、负荷等元件的运行条件,确定电力系统各部分稳态运行状态参数的计算。通常给定的运行条件有系统中各电源和负荷点的功率、枢纽点电压、平衡点的电压和相位角。待求的运行状态参量包括电网各母线节点的电压幅值和相角,以及各支路的功率分布、网络的功率损耗等。(Power flow calculation is a term of power science. It refers to the calculation of the distribution of active power, reactive power and voltage in power network under given network topology, component parameters and generation and load parameters. Power flow calculation is based on the given grid structure, parameters and operation conditions of generator, load and other components to determine the steady-state operation parameters of each part of the power system. Usually, the given operating conditions include the power of each power source and load point, junction voltage, balance point voltage and phase angle. The parameters to be determined include the voltage amplitude and phase angle of each bus node, the power distribution of each branch and the power loss of the network.)
- 2020-06-23 10:00:01下载
- 积分:1
-
Goertzel
用Goertzel算法计算两正弦波信号的相位差(Goertzel algorithm using two-phase sine wave signals)
- 2009-07-04 11:22:43下载
- 积分:1