BW-

UWB，超宽带信号分析必用的子函数，第8部分！(UWB, ultra-wideband signal analysis will be used for Functions, Part 8!)

数字基带传输系统的MATLAB仿真实现 function [sampl,re_sampl]=system_1(A,F,P,D,snr,m,N) 输入变量A ,F,P分别为输入信号的幅度、频率和相位，D为量化电平数，snr 为信道信噪比，N为D/A转换时的内插点数；输出变量sampl为抽样后的输入 信号，re_sampl为恢复出的输入信号。 数字基带传输系统的MATLAB仿真实现 [sampl,quant,pcm]=a_d_1(A,F,P,D) [changed_ami]=signal_encod_1(pcm) [ami_after_channel]=channel_1(changed_ami,snr) [adjudged_ami]=adjudg_1(ami_after_channel,m) re_pcm=signal_decod_1(adjudged_ami) [re_voltag,re_sampl,re_sampl1]=d_a_1(re_pcm,sampl,D,N)(Digital baseband transmission system implementation MATLAB simulation function [sampl, re_sampl] = system_1 (A, F, P, D, snr, m, N) input variables A, F, P, respectively, for the input signal amplitude, frequency and phase , D to quantify the number of electric-ping, snr for the channel signal to noise ratio, N to D/A converter when the interpolation points output variables for the sample after Sampl input signal, re_sampl for the restoration of the input signal. Digital baseband transmission system simulation MATLAB implementation [sampl, quant, pcm] = a_d_1 (A, F, P, D) [changed_ami] = signal_encod_1 (pcm) [ami_after_channel] = channel_1 (changed_ami, snr) [adjudged_ami] = adjudg_1 (ami_after_channel, m) re_pcm = signal_decod_1 (adjudged_ami) [re_voltag, re_sampl, re_sampl1] = d_a_1 (re_pcm, sampl, D, N))

在Windows 操作系统下，以Matlab为操作平台，对一个简单的二阶环进行仿真.(In the Windows operating system, using Matlab for the operating platform for a simple second-order loop simulation.)

本程序是应用ｍａｔｌａｂ程序编写的计算火箭发动机压力对应时间变化程序，程序中的公式和参数可以根据计算时间情况进行修改。(use matlab code to build a function to calculate the presure- time , the equation and paremeter in the code can be modified depended on your need)

说明：  简介卫星姿态控制系统的模型，并针对该模型分析故障发生的特点，故 障诊断的难点，以及可能发生故障的部位和故障的类型，给出故障检测的方法。(Introduction of satellite attitude control system model and the model for the analysis of the characteristics of faults, fault diagnosis of the difficulties, and possible failure location and fault type, fault detection methods are given.)

《MATLAB控制系统仿真与实例详解》的附书光盘文件，包含各章的实例代码。(" MATLAB and Control System Simulation example explanation" of the CD-ROM with the book file, each chapter contains examples of code.)

matlab 信号分析详解(matlab design)

尺度边缘检测，效果还不错的MATLAB代码。(Scale edge detection, the results were good.)

说明：  数字信号处理的一些算法等，包括扩散，衰减，补偿等，对于DSP专业的有一定帮助(err)

说明：  FIR数字滤波器的设计方法主要是建立在对理想滤波器频率特性作某种近似的基础上的。这些近似方法有窗函数法、频率抽样法、最佳一致逼近法。在这里只讨论窗函数法。程序中也是采用了这种方法。(FIR digital filter design method is mainly based on the frequency characteristics of the ideal filter for some kind of approximation on the basis of. These approximate methods are a window function method, frequency sampling method, the best uniform approximation method. Here only to discuss the window function method. Procedure is also adopted this approach.)