OFDM

利用matlab编制直齿圆柱齿轮应力计算程序，并把程序成GUI界面（matlab原理与工程应用（第二版）中的实例加以改编）(Using matlab to prepare spur gear stress calculation program, and the program into a GUI interface (matlab Principles and engineering applications (second edition) instance be adapted))

对信号在AR模型下进行的的yuler_walker,和burg算法谱估计(AR model of the signal under the yuler_walker, and spectral estimation algorithm burg)

车辆系统动力学主动悬架线性最优控制（LQG）程序，在simulink环境下仿真计算出路面输入下的最优主动悬架性能，并于传动被动悬架作出对比(Vehicle System Dynamics active suspension linear optimal control (LQG) program, simulink simulation environment optimal active suspension performance under the road input drive passive suspension)

未来线路预测,分析误差,小波包分析提取振动信号中的特征频率，sar图像去噪的几种新的方法。( Future line prediction, error analysis, Wavelet packet analysis to extract vibration signal characteristic frequency, Several new methods sar image denoising.)

说明：  经典的卷积码的Log_MAP译码算法matlab仿真实现(A classical Log_MAP decoding algorithm of convolutional code is relized by matlab.)

This will give u basic idea about dtc

hht（希尔伯特黄变换）的matlab工具箱，其中包括时频分析工具箱(hht (Hilbert-Huang Transform) of the matlab toolbox, including the time-frequency analysis toolbox)

本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面，点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动，您可以通过使用蛇 1。点击“新形象”，并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)

一个OFDM系统的MATLAB程序 有利于对OFDM通信系统的同步进行研究(An OFDM system, MATLAB procedures are conducive to the synchronization of the OFDM communication system to study)

说明：  泊松均匀分布的WSNs的网络拓扑Matlab程序(Poisson network structure for WSN)