Labview

The structure of the multilayer sequence

说明：  NI DAQ应用介绍 1. 一个完整数据采集系统的基本组成部分 2. NI 提供了基于哪些平台的数据采集硬件产品，它们分别适用于什么样的应用领域 3. 数据采集设备硬件选型过程中应该关注哪些重要参数(Introduction of NI data acquisition hardware 1. Basic components of a complete data acquisition system 2. NI provides data acquisition hardware products based on which platforms and which application areas they are suitable for respectively. 3. What important parameters should be paid attention to in the process of hardware selection of data acquisition equipment)

说明：  抽取不同声音（适应文件）的统计特征、信号处理参数（模式），设计简单的基于适应特征的声音识别程序。(Extract the statistical features and signal processing parameters (patterns) of different sounds (adaptive files), and design a simple voice recognition program based on adaptive features.)

说明：  基于LabVIEW的泰克示波器与计算机的通信(Communication between Tick Oscilloscope and Computer Based on LabVIEW)

基于labview的双通道数据采集回放系统实例参考，内包含程序设计指导书(Labview-based dual-channel data acquisition system instance playback reference, the book contains a programming guide)

说明：  基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)

主要包含经纬高信息、北天东坐标系、地心坐标系之间的坐标转换，用labview实现的。(It mainly includes the coordinate transformation between the latitude and longitude information, the North East coordinate system and the geocentric coordinate system. It is realized by LabVIEW)

CRC16的9个LabVIEW算法CCITT,CCITT-KERMIT,CCITT-X25，CCITT-XMODEM,DNP,IBM,MAXIM,MODBUS,USB，开发环境LabVIEW2013(9 LabVIEW algorithm of CRC16: CCITT,CCITT-KERMIT,CCITT-X25，CCITT-XMODEM,DNP,IBM,MAXIM,MODBUS,USB The development environment version is LabVIEW 2013)

说明：  labview写的串口调试助手，已经调试通过，使用事件驱动编写的(RS232 debuger by labview)

该vi主要是一台简单的单通道数字示波器，实现数据采集、波形显示、信号处理、波形存储等(The main vi is a simple single-channel digital oscilloscope, data acquisition, waveform display, signal processing, waveform storage, etc.)