登录
首页 » Others » KEIL2

KEIL2

于 2013-12-12 发布 文件大小:6KB
0 168
下载积分: 1 下载次数: 2

代码说明:

  在keil上进行单片机语言编程,很实用的小例(Microcontroller programming language on the keil, very practical small cases )

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 128x64LCD
    For the 128x64 type LCD programming. You can read a very particular document.
    2009-09-26 23:12:03下载
    积分:1
  • keypad_matrix
    this a keypad matrix applicable for ZDSII
    2013-12-23 00:42:44下载
    积分:1
  • LED TEST
    说明:  基于STM32F103单片机的LED测试源码(LED Test Source Based on STM32F103 MCU)
    2020-06-23 13:00:06下载
    积分:1
  • jiashiqi
    这是一款空气加湿器,经过高频振荡,把水雾化,采用台系MCU,含有原理图。是一款经过量产的优良小家电产品。(This is an air humidifier, high frequency oscillation water atomization, the Taiwan-based MCU contains schematic. After production is a good small household electrical appliances.)
    2013-04-23 19:34:35下载
    积分:1
  • FM31256
    fm31256读写源程序,(fm31256 literacy program. 0000000000000000000000000000000000000000 )
    2007-06-08 08:09:29下载
    积分:1
  • Sensors
    Application that displays the values of the acceleration sensor graphically.
    2014-06-24 11:23:41下载
    积分:1
  • 10路ADC采集
    说明:  STM32F103芯片用自带AD采集,10路ADC通道采集,通过DMA进行数据传输并在LCD上进行显示(STM32F103 10 ADC channels acquisition, data transmission through DMA and display on LCD.)
    2020-06-24 18:20:02下载
    积分:1
  • QPR_Control
    一个简单的准比例谐振控制器模型,可用于线性分析频率响应(A simple quasi-resonant controller proportional model that can be used to analyze linear frequency response)
    2020-10-15 18:27:29下载
    积分:1
  • ludeng
    该夜用照明灯系统采用AT89S52单片机为核心,利用单片机的端口分别控制LCD1602标准时钟系统、可控硅和电铃,达到智能操控照明系统(The night with the lighting system using AT89S52 microcontroller as the core, using SCM port control the LCD1602 standard clock system, SCR and bells, to the intelligent control lighting system)
    2012-12-06 07:30:56下载
    积分:1
  • STM32+ESP8266+SHELL
    STM32加ESP8266模块,实现UDP透传模式通信,可以通过SHELL命令,获取采集电压和时间信息。在UDP调试工具输入“getcfg”可以获取配置信息 包括单次测量模式 循环测量模式 循环时间间隔设定等等相关参数设置。(STM32 and ESP8266 module are used to achieve UDP transmission mode communication, and the acquisition voltage and time information can be obtained through the SHELL command. In the UDP debugger, input "getcfg" can get configuration information, including single measurement mode, cycle mode, cycle interval setting and so on.)
    2018-02-10 23:51:58下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载