arith

labview倒立摆上位机程序，是2013年9月分全国电子设计大赛的作品，但是可惜的是，电子大赛不能用电脑，很遗憾，发上来让大家参考，写的不好，希望多包涵(labview handstand put crew procedures, 2013 September, 2011 National Design Competition works, but unfortunately, can not use a computer electronic contest, unfortunately, made up for our reference, badly written, I hope more than covered)

基于STC15F104W与DS18B20的温度采集。用LED小灯输出(Collection based STC15F104W with DS18B20 temperature. Output with LED lights)

双步进电机综合控制 用于51单片机 (Dual stepper motor integrated control)

了解 CAN 总线通信原理，实现利用 CAN 总线完成通信 在进行实验的时候，需要将两块开发板连接 USB 线进行充电，因为利用 CAN 总线进 行通信需要有较高的驱动能力。(Learn CAN bus communication theory, to achieve complete CAN bus communication when carrying out the experiment, you will need two development boards connect the USB cable for charging, because the use of CAN bus communication requires a higher drive capability.)

基于stm32在keil平台上通过ds18b20测量温度的实验(ds18b20 temperature measurement)

说明：  在过程控制中，按偏差的比例（P）、积分（I）和微分（D）进行控制的PID控制器（亦称PID调节器）是应用最为广泛的一种自动控制器。它具有原理简单，易于实现，适用面广，控制参数相互独立，参数的选定比较简单等优点；而且在理论上可以证明，对于过程控制的典型对象──“一阶滞后+纯滞后”与“二阶滞后+纯滞后”的控制对象，PID控制器是一种最优控制。PID调节规律是连续系统动态品质校正的一种有效方法，它的参数整定方式简便，结构改变灵活（PI、PD、…）(In process control, the PID controller (also called PID regulator) controlled by deviation ratio (P), integral (I) and differential (D) is one of the most widely used automatic controllers. It has the advantages of simple principle, easy realization, wide application, independent control parameters, simple parameter selection, etc. It can also be proved theoretically that PID controller is an optimal control for the typical object of process control - "first-order lag + pure lag" and "second-order lag + pure lag". System. The regulation rule of PID is an effective method for dynamic quality correction of continuous system. Its parameter setting method is simple and its structure is flexible (PI, PD,...).)

本编程手册介绍了如何烧写STM32F101xx、STM32F102xx和STM32F103xx微控制器的闪存存储器。(This programming manual describes how to burn the flash memory of STM32F101xx, STM32F102xx and STM32F103xx microcontrollers.)

说明：  PWM输入+DMA，亲测可用，有需要的朋友可以自行下载。(PWM input + DMA, pro-test available.)

51单片机的串口通信程序，来自于开发板，VC环境下编写。(51 the Serial communication program, and from the development board, VC environment prepared.)

说明：  设计一个正弦信号发生器，使用凌阳公司的16位单片机SPCE061A作为中央控制器，结合DDS芯片AD9850，产生0～15MHz频率可调的正弦信号,正弦信号频率设定值可断电保存；使用宽频放大技术，在50Ω负载电阻上使1K～10MHz范围内的正弦信号输出电压幅度VP-P=6V±1V；产生载波频率可设定的FM和AM信号；调制信号为1KHz的正弦波，调制信号的产生采用DDS技术，由CPLD和Flash ROM加上DAC进行直接数字合成；二进制基带序列码由CPLD产生，在100KHz固定载波频率下进行数字键控，产生ASK，PSK信号。(Design of a sinusoidal signal generator, the use of Sunplus 16-bit MCU SPCE061A as the central controller, combined with DDS chip AD9850, have adjustable frequencies 0 ~ 15MHz sinusoidal signal, sinusoidal signal frequency settings can be stored power using broadband amplification, in a 50Ω load resistor to 1K ~ 10MHz sinusoidal signal within the output voltage amplitude VP-P = 6V ± 1V generating the carrier frequency of the FM and AM can be set signal 1KHz sine wave modulation signal, modulated signal generation using DDS technology, coupled by the CPLD and Flash ROM DAC for direct digital synthesis binary baseband sequence code generated by the CPLD in a fixed carrier frequency 100KHz digital keying, resulting in ASK, PSK signals.)