登录
首页 » matlab » boost_PCM_simulink_in

boost_PCM_simulink_in

于 2009-03-10 发布 文件大小:1KB
0 409
下载积分: 1 下载次数: 344

代码说明:

  基于平均法的boost型DC/DC建模步骤,包括电压模和峰值电流模。增加了误差放大器放大倍数的确定,电源调整率,负载调整率和三种变换器的一阶等效模型(Based on the average of the boost-type DC/DC modeling steps, including the voltage mode and peak current mode. An increase of the error amplifier to determine the magnification, adjust the rate of power supply, load-adjusted factor and three first-order equivalent converter model)

文件列表:

boost_PCM_simulink_in.m

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • wigner-ville-frft
    魏格纳分布及分数阶傅里叶变换结合的LFM信号处理算法(LFM signal processing algorithms Wigner distribution and fractional Fourier transform combined)
    2014-09-05 09:35:53下载
    积分:1
  • yunchouxue
    运筹学中非线性规划的牛顿法,梯度法,直接法,内点法的matlab 实现(Nonlinear Programming Operations Research Newton method, gradient method, direct method, interior point method implementation matlab)
    2010-11-24 20:15:57下载
    积分:1
  • MELP_m
    melp algorithm 2.4kbs code in matlab
    2011-01-13 15:23:24下载
    积分:1
  • MATLABprogramming
    matlab编程的入门教材,适合初学者阅读,本书由浅入深,逐步推进地说明编程的各个注意点(matlab programming primer for beginners to read, the book progressively, step by step description of each programming point of attention)
    2011-11-28 20:18:13下载
    积分:1
  • l1magic-1.1
    说明:  基于matlab的稀疏表示中L1范数计算源码(the codes for L1 in sparsty representation with matlab)
    2009-08-11 09:22:54下载
    积分:1
  • 200707171150141339
    这个Matlab程序实现一个基于活动轮廓的边缘检测,而不进行重新初始化。(The Matlab program of active contour based on edge detection, rather than re-initialization.)
    2009-05-13 09:09:53下载
    积分:1
  • numericalanalysis
    本工具包给出了数值分析这门课程中所涉及的所有问题所需程序。很不错(The kit gives the numerical analysis in this course all the issues involved in the necessary procedures. Very good)
    2010-11-24 10:10:10下载
    积分:1
  • MATLAB-lesson-plans
    matlab程序的PPT教案及实例源代码,以及相关矩阵概念的补充(Matlab PPT example case and source code, and related matrix of the concept of added)
    2012-04-11 15:40:43下载
    积分:1
  • MATLAB-SSB
    基于MATLAB的 SSB调制解调实现.利用MATLAB集成环境下的M文件,编写程序来实现SSB的调制解调,并绘制出解调前后的时域和频域波形及叠加噪声时解调前后的时频波形,根据运行结果和波形来分析该解调过程的正确性及信道对信号传输的影响。(MATLAB-based SSB modulation and demodulation to achieve. Advantage of MATLAB M-files integrated environment, programming to achieve SSB modulation and demodulation, and draw out the time before and after demodulation and frequency demodulation waveform and the superimposed noise before and after the time when frequency waveform, according to analysis of operating results and the waveform of the demodulation process of the correct and the channel on the signal transmission.)
    2010-07-07 11:02:34下载
    积分:1
  • xiaoboquzao
    本程序能实现小波模极大值算法去除脉冲噪声,效果明显。(This procedure enables on wavelet modulus maxima algorithm to remove impulse noise, the effect clearly.)
    2009-11-09 16:32:27下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载