ADT-22.0.1

说明：  实现正常时钟功能，带时间日期，三组闹钟，键盘显示(流程图，配合程序使用)(Realize normal clock function, with time and date, three sets of alarm clocks, keyboard display)

at91sam9269 recovery flash

stm32f4 adc 的代码，双通道，用DMA保存数据。(stm32f4 family c code, adc This example provides a short description of how to use the ADC peripheral to convert a regular channel in Dual interleaved mode using DMA in mode 3 with 5Msps. DMA mode 3 is used in interleaved mode in 6-bit and 8-bit resolutions. The Dual interleaved delay is configured 6 ADC clk cycles. On each DMA request (two data items are available) two bytes representing two ADC-converted data items are transferred as a half word. The data transfer order is similar to that of the DMA mode 2. A DMA request is generated each time 2 data items are available 1st request: ADC_CDR[15:0] = (ADC2_DR[7:0] << 8) | ADC1_DR[7:0] 2nd request: ADC_CDR[15:0] = (ADC2_DR[7:0] << 8) | ADC1_DR[7:0] The ADC1 and ADC2 are configured to convert ADC Channel 12, with conversion triggered by software. By this way, ADC channel 12 is converted each 6 cycles. In this example, the system clock is 168MHz, APB2 =84MHz and ADC clock = APB2 /2. Since ADCCLK=)

STM32单片机的库函数STM32F10x_StdPeriph_Lib_V3.5.0(STM32f103 lib STM32F10x_StdPeriph_Lib_V3.5.0)

方案组成模块及系统框图 本方案设计主要由以下模块组成 1：顶层模块 2：数据输入排序模块 3：系统控制模块 4：RAM控制器模块 5：ROM控制器模块 6：蝶型单元模块(Program composition module and system diagram The design of this scheme is mainly composed of the following modules 1: top module 2: data input sorting module 3: system control module 4:RAM controller module 5:ROM controller module 6: butterfly type unit module)

飞思卡尔M0+ 系列 kl05开发板资料源代码 (freescale kl05 demo board sources code)

说明：  是一本关于C语言跟单片机接口的书,还可以.反正我看了很好.不知道是否适合你.(Is on a single-chip interface with C language book, also. Anyway, I saw very good. Do not know if for you.)

8、可变频率方波发生器 用单片机的定时器设计一个频率可变的方波发生器，输出频率范围1Hz~500Hz，频率输出精度为0.5Hz。要求可以实时显示当前输出的频率，可以用键盘来设定方波发生器的输出频率，具有直接设定或逐渐调节的功能，调节分辨率和显示分辨率均为0.5 Hz，其它电路自由发挥。(8, variable frequency square wave generator with single-chip microcomputer timer design a variable frequency square wave generator, the output 1 Hz ~ 500 Hz frequency range, frequency output precision is 0.5 Hz. Requirements can real-time display current output frequency, can use the keyboard to set the output frequency of square wave generator, has the function of directly set or adjust gradually adjust the resolution and display resolution of 0.5 Hz, free play other circuits.)

led relation document

这是基于STM32和FPGA的简易数字存储示波器(This is Simple Digital Storage Oscilloscope Based on STM32 and FPGA)