yipeiw-detect-ICASSP2014

ModbusMaster 基于modbus的网络编程，可读写(ModbusMaster based on Modbus network programming, read and write)

这是一个用51单片机系统仿真ucosii工作的protues电路 本系统包括扩展64k RAM的单片机系统和杨屹移植到51单片机的ucosii 系统 使用方法： 1.安装Protues7.4版，然后用protues打开protues 8051 simulation 文件夹 中的extern ram.DSN 文件 2.打开extern ram.DSN 后，双击单片机在弹出的窗口中的Program File 选项 中选择yy.hex文件。 (yy.hex其实就是yy文件夹中keil文档编译出来的hex文 件，yy文件夹是杨屹的ucos51 系统，用keil 2 可以打开) 3.在Clock Frequency选项中输入22.184M(杨屹的ucos51 用的是22.184M hz的单片机频率) 4.双击VTERM串口调试显示屏，在Baud Rate 选项中选择19200的波特率 5.保存，点击运行就可以看到经典的hello world 了。 (1. Protues7.4 version installed, and then open the protues folder protues 8051 simulation The extern ram.DSN file 2. Open extern ram.DSN, double-click the pop-up window of SCM in the Program File option, select yy.hex file. (yy.hex actually yy folder keil out of the document compiled hex files, yy folder is Yang Yi s ucos51 system, using keil 2 Can open) 3. In the Clock Frequency option to enter 22.184M (Yang Yi of the ucos51 using a microcontroller 22.184M hz frequency) 4. Double-click VTERM serial debug display, in the Baud Rate select 19200 baud rate options 5. Save, click Run you can see the classic hello world)

Compileded example for sim908 embedded AT Burn at 0x004000 address with embedded at core

STC芯片烧写软件,专用于STC芯片的单片机程序烧录(STC chip programmer software)

单片机程序 用定时器定时 DA0832实现DA(Microcontroller program to achieve with the timer time DA0832 DA)

基于AD7606的数据采集系统的软件程序（STM32F103）(software of AD7606（STM32F103）)

通过STM32F407内置的12位adc对外部的模拟信号进行采集，利用DMA进行数据传输以提高CPU的使用效率，最后将ADC采集到的数据显示在3.4寸的液晶触摸屏上。(Through the 12 bit STM32F407 built-in ADC external analog signal acquisition, using DMA data transmission, in order to improve the use efficiency of CPU, and finally the data collected by ADC display on the 3.4 inch LCD touch screen.)

手机APP通过蓝牙连接上小车，可以简单的控制小车的前后左右。(Remote control of single chip microcomputer by mobile APP)

SIM900开发板配套STM32 GPRS代码(SIM900 STM32 GPRS driver)

说明：  自己画的开发板，用的STM32F103VGT6芯片，代码中使用了很多功能，基本的I2C，SPI，Flash读取，串口通信（WIFI，Enocean协议），等都有涉及，驱动代码不全是自己写的，所以有些地方没去在意备注，但是每个使用修改的地方都有我自己的备注，基本上就是自己的开发板，自己在研究学习验证的过程中一点一点整合起来的(I drew my own development board and used stm32f103vgt6 chip. Many functions were used in the code, such as basic I2C, SPI, flash reading, serial communication (WiFi, enocean protocol), and so on. The driver code was not written by myself, so some places didn't pay attention to the remarks, but every place I used and modified had my own remarks, which was basically my own development board In the process of research, learning and verification, I integrated them bit by bit)