wavelet-denoise-GUI-package

C龙贝格算法　　源程序 ｍａｔｌａｂ数值计算 ()

惯性导航解算程序，四阶龙格库塔发更新四元数，求姿态、速度和位置(Solver inertial navigation procedures, fourth-order Runge-Kutta issued to update the quaternion, seeking attitude, velocity and position)

将一个512×512的lena.bmp图像进行DCT变换，对得到的DCT系数按8×8块进行分层（分三层），重组填充得到新的系数矩阵，结果发现原图像的能量集中在了新图像的左上角低频部分。(The lena.bmp an image of 512 × 512 is subjected to DCT transform, the DCT coefficients obtained by layering 8 × 8 block (of three), to obtain a new recombinant filling coefficient matrix, the energy of the original image is found concentrated in upper left corner of the low-frequency part of the new image.)

接收端采用的算法和程序流程与发送端发送的OFDM符号的帧结构有关系。具体的帧结构，以及定时估计，频偏估计，剩余误差跟踪的算法可参考算法说明文档。这里对程序的流程进行说明。 首先根据短训练字的特性进行相关运算，进行信号到达检测，当检测到相关值大于门限一定次数后，认为有信号到达。然后根据长训练字的特性，进行相关运算，进行OFDM符号FFT窗口起始位置的估计。估计出FFT窗口的位置后，先在时域进行小频偏的估计，将两个长训练字进行小频偏补偿后，进行FFT运算，根据FFT运算的结果进行整数倍频偏的估计。这些参数估计完成后，就可以进行数据解调了。先对数据部分进行完整的频偏补偿，然后根据估计的FFT窗口位置进行FFT运算得到频域的数据，进行解调。然后在对应于导频的子载波位置上提取出导频信息，根据导频信息估计出剩余定时误差以及剩余的信道响应误差，将误差量送入环路进行跟踪。当收到所有数据后，重新回到信号到达检测状态，进行下一次信号到达的检测和信号接收。 (The receiving end uses the algorithm and the program flow and the frame structure of the OFDM symbol transmitted by the sending end. Specific frame structure, and timing estimation, frequency offset estimation, residual error tracking algorithm can refer to the documentation. Here to illustrate the process of the program. First, according to the characteristics of the short training word correlation operation, the signal reaches the detection, when the correlation value is greater than the threshold of a certain number of times, that there is a signal to reach. Then, according to the characteristics of the long training word, the correlation operation is carried out, and the initial position of the OFDM symbol FFT is estimated. The estimated position of the FFT window, first in the time domain for small frequency offset estimation, two long training word for small frequency offset compensation, the FFT operation. According to the result of FFT for integer frequency bias estimation. Af)

说明：  用Gardner算法时钟同步的BPSK的源程序(Gardner algorithm for clock synchronization with the source code BPSK)

基于BP神经网络的ＰＩＤ控制 绝对能运行的(Based on BP neural network PID control can certainly run)

本压缩包是关于二进制ASK调制方式的MATLAB实现，大家可以试一下。(This zip is a modulation of imply 2ASK,and everyone can have a try.)

interaction image processing segmentation tools

this source code is eacfault matlab

this file is about risk managment in marketing....