paper1

利用小波进行图像压缩，使用的是一代小波对图像进行的压缩(image compress using wavelet)

说明：  国外编写的仿真程序，利用Simulink软件对波音747飞机进行仿真，很有参考价值(The preparation of the simulation program abroad, the use of Simulink software for Boeing 747 aircraft simulation, useful reference)

收费站排队仿真程序，动画实时显示，指标事实输出(Toll station queuing simulation program)

Veritas filesystem driver - object location table support.

此代码是用MATLAB进行对数据做FFT变换(This code is done using MATLAB FFT transform data)

假设截获了一段短波数字通信的信号，要求解调出最终的信息，每组解调出来后，将10组信息组合起来，恢复最终的信源输出数据。 先验信息：两组数据文件，编号为1、2，每组I、Q两路存放，格式为“int16”，采样率为9600Sa/s，其中第一组为单径情况，第二组为多径情况。 参数符合MIL-STD-188-110A标准； 同步序列为syn=seq.dat，BPSK调制； 接收机频率稳定度高于1e-6。 文件中有效信息总长度为333.75s，其中同步头长为5/12s，每时隙1/6s，训练序列占10 ，在数据之前； 交织方式为全交织，矩阵交织，列为1000，在比特级进行； 纠错码码率为1/2； 调制方式为BPSK、QPSK和8PSK中的一种，映射方式为二进制，BPSK相位偏移为0，其余两种为 。 (Suppose intercepted signal for a period of short-wave digital communications requires final demodulated information after each demodulated, combining 10 group information, to restore the final output data source. Priori information: two sets of data file, numbered 1, 2, each I, Q two-way storage, the format is int16 , sampling rate 9600Sa/s, where the first group is a single path, the second group multipath situation. Parameters meet MIL-STD-188-110A standard Synchronization sequence syn = seq.dat, BPSK modulation The frequency stability of the receiver is higher than 1e-6. File payload total length of 333.75s, wherein the synchronization header length is 5/12s, each time slot 1/6s, accounting for 10 of the training sequence, before the data Interleaving for the whole interleaving matrix interleaving, as 1000, carried out at the bit level Error correction code rate of 1/2 The modulation scheme is BPSK, QPSK and 8PSK one, a binary mapping, the BPSK phase offset is 0, the )

结构动力学算例，运用mirison和matlab语言，写了一个波浪力的算例(A numerical example of structural dynamics is given. a numerical example of wave force is written by using mirison and MATLAB language.)

共轭梯度发法matlab版本的一个实例源代码，带轨迹收敛图(a source code of conjugate gradient algorithm by matlab )

DC dynamic braking is obtained when the stator of an induction motor running at a speed is connected to a dc supply.dc current flowing through the stator produces a stationary magnetic field.Motion of rotor in this field induces voltage in the rotor winding.Machine therefore works as a generator.Generated energy is dissipated in the rotor circuit resistance,thus giving dynamic braking.

基于DWT的数字水印嵌入算法，已进行过调试，可以直接使用(DWT-based digital watermarking algorithm, has been commissioning, can be used directly)