登录
首页 » matlab » zhuangxiang

zhuangxiang

于 2015-03-03 发布 文件大小:1KB
0 301
下载积分: 1 下载次数: 23

代码说明:

  利用遗传算法解决一维装箱问题,包含了数据初始合理化,交叉变异的过程(The use of genetic algorithms to solve the one-dimensional packing problems, including the initial data rationalization, crossover and mutation process)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • CP0701
    这是高斯脉冲的波形变化源代码,它是仿真超宽带波形的脉冲形成器的基础。 (This is the Gaussian pulse waveform changes in the source code, it is ultra-wideband waveform simulation of the pulse-forming the basis.)
    2006-06-13 08:33:02下载
    积分:1
  • Simulink
    一个simulink的仿真课件,通俗易通,自己感觉挺好(A simulink simulation courseware, popular ETS, he felt very good)
    2013-09-02 09:12:42下载
    积分:1
  • 驾驶员模型数据处理
    驾驶员模型数据处理,论文第二章仿真程序,发表sci(Pilot model data processing, paper chapter ii simulation program, published sci)
    2015-04-21 15:08:40下载
    积分:1
  • sphere
    拟合球面的程序,给定一些数据后,可以绘制球面,用于分析测量数据(Sphere fitting procedures, given some data, you can draw the sphere, for the analysis of measurement data)
    2011-10-09 21:18:51下载
    积分:1
  • VMD
    说明:  VMD是一种自适应、完全非递归的模态变分和信号处理的方法。(VMD is an adaptive, completely non-recursive method of modal variational and signal processing.)
    2020-09-22 21:35:16下载
    积分:1
  • getZNparam
    PID控制算法中,根据一节延迟传递函数的放大倍数K、延迟时间L和时间常数T,获得PID中比例环节、微分环节和积分环节的参数(PID control algorithm, according to a delay in the transfer function of magnification K, the delay time L and time constant T, to obtain the proportion of PID in the link, differential and integral link in the parameters of link)
    2009-07-09 11:35:56下载
    积分:1
  • nihejianyan
    已调试好的数据分布的拟合与检验的matlab程序源代码,内容有卡方拟合优度检验、jbtest函数检验、Kolmogorov-Smirnov检验和画频率直方图(failed to translate)
    2011-08-10 07:05:24下载
    积分:1
  • GA_Knapsack
    有关多背包问题的遗传算法,非常不错,对初学者很有帮助(For multiple knapsack problem genetic algorithm, very good, very helpful for beginners)
    2013-11-17 20:48:21下载
    积分:1
  • NPearson
    奈曼皮尔逊准则仿真,在P(H1|H0)=a的约束条件下,使P(H1|H1)最大的准则。(Neyman-pearson criterion)
    2018-04-22 11:40:54下载
    积分:1
  • velocity_filtering_based_on_make_zeta_output_0
    This code uses the output from either make_zeta_u.c file or make_zeta_v.file i.e. it uses the velocity data at any z-level specified by zlevel1. Furthermore, this code filters the velocities, plots the filtered and raw signals at certain specified locations and then creates maps of the velocity time series
    2011-06-06 11:26:54下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载