jianpan

自动交通控制系统用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁示线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示）(Automatic traffic control system using red, green, yellow light-emitting diodes, said a total of three traffic lights, the use of single-chip analog time display on a regular traffic signal control and management. Changes of lights to be as follows: 1) Release Line: green clearance 25 seconds, the yellow light warning for 5 seconds, then the red light is prohibited. 2) ban shows lines: the red light is prohibited for 30 seconds, then the green light to release. 3) When the red light in one direction, if the direction of the car through, the alarm speaker sound. (Hit the red signal available 3-5V analog representation))

stm32芯片--用GPIO口模拟I2C驱动MPU6050陀螺仪(Stm32 chip- using GPIO port simulation I2C driver MPU6050 gyroscope)

由于太阳能充电系统多在户外，为了方便研究太阳能充电控制系统对蓄电池的充电情况，本文使用GPRS无线传输技术，设计了一套太阳能充电系统蓄电池的充电电压电流远程实时监测系统。系统的硬件部分由电压电流检测电路、单片机STC89C52RC、GPRS模块SIM300以及相应的外围电路构成，下位机软件由C语言编写并与硬件部分构成系统下位机部份，实现了对充电电压电流的信息采集以及数据的无线数传。上位机在LabVIEW2010环境下编写，具备友好的人机交互界面，实现了数据的远程接收、实时显示、数据库管理、报表生成和打印等功能。经过系统测试系统实现了对电压电流的远程监测。(As the solar charging system more outdoors, in order to facilitate the study of solar charge control system for charging the battery case, we use GPRS wireless transmission technology, we designed a solar charging system battery charge voltage and current remote monitoring system. The hardware part of the system by the voltage and current detecting circuit, microcontroller STC89C52RC, GPRS module SIM300 and corresponding peripheral circuits, lower computer software written in C language and hardware parts lower position machine part of the system, the realization of the charging voltage and current information collection and wireless data transmission of data. PC at LabVIEW2010 prepared environment, with friendly interactive interface, realize the remote receiving data, real-time display, management, report generation and printing. After the system test system enables remote monitoring of voltage and current.)

基于MSP430单片机下的GSM模块开发源代码(MSP430 microcontroller development under the GSM)

很好的一个东西，希望对大家有所帮助，这是关于DS1302的一个程序(Good thing, we want to help, this is a program on DS1302)

Richard Kaiser C++ mit Microsoft Visual C++ 2008

二维弹性常值边界元程序BEM2C++，二维边界元，弹性静力学(2 Dimensional elastic constant BEM program BEM2C++)

stc12c5a60s_spi直接驱动st7920(12864) 串口驱动、只用个IO口(stc12c5a60s_spi direct drive st7920 (12864) serial driver, only with a IO port)

步进电机是将电脉冲信号转变为角位移或线位移的开环控制电机，是现代数字程序控制系统中的主要执行元件，应用极为广泛。。在非超载的情况下，电机的转速、停止的位置只取决于脉冲信号的频率和脉冲数，而不受负载变化的影响，当步进驱动器接收到一个脉冲信号，它就驱动步进电机按设定的方向转动一个固定的角度，称为“步距角”，它的旋转是以固定的角度一步一步运行的。可以通过控制脉冲个数来控制角位移量，从而达到准确定位的目的；同时可以通过控制脉冲频率来控制电机转动的速度和加速度，从而达到调速的目的。(Stepper motor is an open loop control motor which transforms electrical pulse signal into angular displacement or linear displacement. It is the main executive element in modern digital control system, and is widely applied. In the case of non overloaded, the motor speed and stop position depends only on the pulse frequency and pulse number, regardless of load changes, when the stepper driver receives a pulse signal, it drives stepper motor to set the direction of rotation of a fixed angle, called "step", it is the rotation of the fixed point of the operation step by step. We can control the angular displacement by controlling the number of pulses, so as to achieve the goal of accurate positioning. At the same time, we can control the speed and acceleration of motor rotation by controlling the pulse frequency, so as to achieve the purpose of speed regulation.)

128KHzID卡读卡模块程序，带模块原理图，曼切斯特解码(128KHzID card reader module program with block diagram, Manchester decoding)