dm365-adc-linux_drive

STM8s003+AT24C32+125Khz RF读卡程序(STM8 125Khz RF reader program)

这是小车程序，往年的比赛题目（小车过跷跷板），用的是ATmega16单片机，在CV的编译环境下。(Car program in previous years, the game title (car seesaw), ATmega16 microcontroller, CV, compiler environment)

智能小车使用遥控控制的源代码，本代码可以作为进一步研究的参考(Smart car using the remote control of the source code, the code can be used as reference for further research)

单片机lcd2864 MEUN菜单程序 已经调试好了。(LCD Menu)

雾化器源码，这个是完整的项目，已经量产过的.采用的是SOC的51内核单片机开发.(Atomizer source code, this is a complete project, has production too. Using the 51 kernel MCU SOC.)

大多数自行车速度表工作通过使用霍尔效应传感器固定在自行车前叉。磁铁是附加到前轮上的辐条之一,它将与霍尔效应开关一次革命的车轮。速度计监测传感器计数轮革命。如果知道车轮的直径,距离可以很容易地计算如果你知道有多少革命的车轮。此外,如果时间完成革命,平均速度也可以计算出来。 对于这个问题,您将编写一个程序来确定总距离(英里)和平均速度(英里每小时)考虑到车轮直径,革命的数量和总时间的旅行。你可以假定前轮从未离开地面,并没有下滑或打滑。(Most bicycle speedometers work by using a Hall Effect sensor fastened to the front fork of the bicycle. A magnet is attached to one of the spokes on the front wheel so that it will line up with the Hall Effect switch once per revolution of the wheel. The speedometer monitors the sensor to count wheel revolutions. If the diameter of the wheel is known, the distance traveled can be easily be calculated if you know how many revolutions the wheel has made. In addition, if the time it takes to complete the revolutions is known, the average speed can also be calculated. For this problem, you will write a program to determine the total distance traveled (in miles) and the average speed (in Miles Per Hour) given the wheel diameter, the number of revolutions and the total time of the trip. You can assume that the front wheel never leaves the ground, and there is no slipping or skidding.)

通过matlab建立整车模型，求汽车的平顺性，本程序求得是汽车在不同等级路面上的悬架动挠度。(Suspension dynamic deflection)

adi公司的aduc7026开发板配套程序(adi' s aduc7026 development board supporting procedures)

利用MSP430单片机实现5分钟倒计时。用Timer_A实现1s定时，4位共阳型数码管显示时间，显示格式为：“x-xx”，分别代表“分”、“十秒”和“秒”。每隔1s，倒计时器的时间减1，倒计时从4分59秒开始计时，至0分0秒结束，停止计时。(MSP430 microcontroller is used to realize 5 minute countdown. Timer_A is used to realize 1s timing and 4-bit common-sun digital tube display time. The display format is "x-x x", representing "minutes", "ten seconds" and "seconds" respectively. Every 1s, the countdown time is reduced by 1. The countdown time starts at 4:59 seconds and ends at 0:0 seconds.)

基于msp430FE425自行车速度表，包含软件和设计报告(well)