登录
首页 » matlab » l1benchmark

l1benchmark

于 2013-11-19 发布 文件大小:114KB
0 226
下载积分: 1 下载次数: 5

代码说明:

  src 算法中的迭代算法,通过该算法可以计算SRC的参数,通过使用线性表示来求。(src algorithm iterative algorithm, the algorithm can be calculated by the SRC parameter, by using a linear representation requirements.)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • fusetool
    图像融合的matlab工具包,希望大家能用得到。(Image fusion matlab toolkit, hope everyone can get.)
    2020-09-15 15:47:56下载
    积分:1
  • BCG-and-ECG-monitor-based-on-msp430
    实现ECG和BCG信号采集和同步监测,对采集的信号进行了特征量提取并作出相应诊断,波形显示在液晶屏上。(Achieve ECG and BCG signal acquisition and simultaneous monitoring of the collected signals feature extraction and make the appropriate diagnosis, the waveform displayed on the LCD screen.)
    2020-06-30 17:20:02下载
    积分:1
  • NuMicro-NUC100-Series-Driver-Reference-Guide
    NuMicro NUC100 Series Driver Reference Guide
    2014-10-17 23:00:11下载
    积分:1
  • mapping
    QPSK,16QAM,64QAM星座图映射,是信号处理的基础,具有参考价值(QPSK, 16QAM, 64QAM constellation mapping, is the basis for signal processing, with the reference value)
    2011-10-19 16:21:25下载
    积分:1
  • Time-Frequency_Analysis_toolbox
    matlab时频分析工具箱,其中包含调幅信号,调频信号,相位编码信号,阶跃信号等等(Time-Frequency Analysis toolbox )
    2011-01-11 22:17:46下载
    积分:1
  • NSGA-III
    测试可以跑,根据自己情况修改下函数即可. NSGA-III 首先定义一组参考点。然后随机生成含有 N 个(原文献说最好与参考点个数相同)个体的初始种群,其中 N 是种群大小。接下来,算法进行迭代直至终止条件满足。在第 t 代,算法在当前种群 Pt的基础上,通过随机选择,模拟两点交叉(Simulated Binary Crossover,SBX)和多项式变异 产生子代种群 Qt。Pt和 Qt的大小均为 N。因此,两个种群 Pt和 Qt合并会形成种群大小为 2N 的新的种群 Rt=Pt∪Qt。 为了从种群 Rt中选择最好的 N 个解进入下一代,首先利用基于Pareto支配的非支配排序将 Rt分为若干不同的非支配层(F1,F2等等)。然后,算法构建一个新的种群St,构建方法是从 F1开始,逐次将各非支配层的解加入到 St,直至 St的大小等于 N,或首次大于 N。假设最后可以接受的非支配层是 L层,那么在 L+ 1 层以及之后的那些解就被丢弃掉了,且 St FL中的解已经确定被选择作为 Pt+1中的解。Pt+1中余下的个体需要从 FL中选取,选择的依据是要使种群在目标空间中具有理想的多样性。(The test can run and modify the function according to its own situation. NSGA-III first defines a set of reference points. Then the initial population containing N individuals (preferably the same number of reference points as the original literature) was randomly generated, where N was the size of the population. Next, the algorithm is iterated until the termination condition is satisfied. On the basis of current population Pt, the algorithm simulates two-point crossover (SBX) and polynomial mutation to produce offspring population Qt by random selection.)
    2021-01-26 22:38:41下载
    积分:1
  • MATLAB
    this program is part of funtion to do a antenna yagi
    2014-12-16 09:12:13下载
    积分:1
  • DVR-SIMULATION--MATHLAB-MDL
    DVR SIMULATION ON MATLAB VERY USEFUL
    2015-03-03 20:04:08下载
    积分:1
  • source-program
    源程序求解二维导热与对流问题,MATLAB编程,有限体积法(Solving the source of two-dimensional heat conduction and convection, MATLAB programming, finite volume method)
    2015-12-05 12:35:56下载
    积分:1
  • yy
    说明:  基于matlab语音短时频谱分析,到谱分析,语谱图分析及结果(Matlab voice-based short-time spectral analysis, the spectral analysis, spectrum analysis and the results of language)
    2008-04-08 10:27:16下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载