Simulated-annealing-for-ftv170.atsp

本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面，点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动，您可以通过使用蛇 1。点击“新形象”，并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)

Music算法，用来计算波源方向，也就是AOA(到达角度）(music algorithm used to calculate the angle of arrival)

OFDM系统 发射、接收源程序，还有一篇文章说明哦，是OFDM系统学习不错的例子(OFDM system transmitter and receiver of the source, there is an article note Oh, OFDM system is a good example of learning)

采用配电网各个节点对电压灵敏度的不同计算分布式光伏最大接入容量(Each node uses a different calculation of the distribution network of distributed PV voltage sensitivity maximum access capacity)

MATLAB program for APT image decoding. Use of the envelope detection. Processing of a WAV file, creating image

Simulates MPSK Modulator/Demodulator. Simulink Platform - Matlab 7.0

本程序是移动协作定位算法的仿真程序，各种条件下的代码都有，可以直接运行。(This progrem is a mobile cooperative localization algorithm, various conditions have the code, can be directly run.)

有限元PlaneTrussElement的matlab程序(FEA PlaneTrussElement)

先进PID控制 MATLAB仿真 第2版 刘金琨等编著和书中的所有程序，模糊控制及其MATLAB应用 张国良，是很好的学习模糊控制的资料。(Advanced PID control of MATLAB version 2 Jin-kun liu huang, and all the procedures of the book, such as fuzzy control and its application MATLAB RON cheung, is a very good learning fuzzy control information.)

线性规划及非线性规划的经典matlab代码，文件中还有PPT文件作为参考学习。(Linear programming and nonlinear programming of the classical code, the document have PPT file as a reference study.)