bubble-sort

此系统是本人做毕业设计时候的老东西了，是汇编写的。可以在PROTEUS上仿真，实际效果和仿真效果一模一样，电梯的功能相信大家都很了解，我就不在这多讲了。但要说明的一点是：我这个系统是仿真用的，有些东西不能和现实中的电梯相比，里面可能有某些方面考虑的不是很周到，希望有心的朋友提点意见，谢谢我的E-MAIL:qq317999920@163.com-This system is designed when I graduated to do the old things is a compilation of writing. Be able to PROTEUS on the simulation, the actual results and simulation of the effect of exactly the same as the functions of elevator think we all understand that I am not in this more than a speech. But the point is to explain: I used this system is the simulation of, some things can not be compared to the reality of the elevator, which may have to consider certain aspects of the not very thoughtful, I hope interested提点意见Friend, thank you my E-MAIL: qq317999920@163.com

电动车从起跑线出发（车体不得超过起跑线），沿引导线到达B点。在“直道区”铺设的白纸下沿引导线埋有1~3块宽度为15cm、长度不等的薄铁片。电动车检测到薄铁片时需立即发出声光指示信息，并实时存储、显示在“直道区”检测到的薄铁片数目。 （2）电动车到达B点以后进入“弯道区”，沿圆弧引导线到达C点（也可脱离圆弧引导线到达C点）。C点下埋有边长为15cm的正方形薄铁片，要求电动车到达C点检测到薄铁片后在C点处停车5秒，停车期间发出断续的声光信息。 （3）电动车在光源的引导下，通过障碍区进入停车区并到达车库。电动车必须在两个障碍物之间通过且不得与其接触。 （4）电动车完成上述任务后应立即停车，但全程行驶时间不能大于90秒，行驶时间达到90秒时必须立即自动停车。 -err

51开发MP3应用程序-51 the development of MP3 applications

这是利用C语言和汇编语言编译的利用取表方式设计的广告灯(This is done using C and assembly language compiled table designed in a way to take advantage of advertising lights)

C51 驱动程序 6610LCD使用nxp的lpc2148控制.rar， 试合刚刚学习者-DISPLAY LCD C51 PGM

输入一串数字，将会自动判断是不是判断闰年程序(Enter a number that will automatically determine the program is not to judge a leap year)

1. 本程序中，首先应输入一个值赋给初始报数上限m，人数n应为任意的，程序应能自动保存出列人的序号并将出列的人所持的密码赋给m，再次作为报数上限，然后删除出列人信息。如此循环，直至所有人都出列为止。 2. 程序以用户和计算机的对话方式执行，即在计算机屏幕上显示“提示信息”之后，由用户在键盘上输入相应数据（即每个人所持的密码），每个人的序号由程序自动分配并存储。 -1. This process should first enter a value assigned to the initial reported that the maximum number of m, the number n should be arbitrary, the procedure should be able to automatically save a number of people out and held out the password assigned to m again reported as the maximum number, and then delete the information out of people. Such a cycle, until all that far out. 2. Procedures to computer users and the implementation of the dialogue, that is displayed on the screen in the computer " message" after the keyboard by the user in the corresponding input data (that is, each person" s password), each individual" s serial number automatically assigned by the procedures and stored.

Aproximaciones Sucecivas en C#

用matlab编写的关于用传输矩阵法计算一维光子晶体的透射率随周期数变化的程序,感觉非常有用-using Matlab prepared on the use of the transfer matrix method one-dimensional photonic crystal with the transmission cycle Change The procedure, a very useful

一个很好的读写硬盘主引导区的程序. 适合于改进后做一键还原及BOOTMANAGER 等软件. -a good master boot drives to read and write the procedures. Suitable for improvement after doing a bond reduction and BOOTMANAGER software.