登录
首页 » matlab » wimax-physical-layer-simulation-code

wimax-physical-layer-simulation-code

于 2011-12-07 发布 文件大小:10KB
0 270
下载积分: 1 下载次数: 20

代码说明:

  wimax physical layer simulation code

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Untitled
    this is acode which is usefull for code processing
    2010-11-16 21:08:30下载
    积分:1
  • MVDR_w
    MVDR和基于认知的MVDR波束形成的比较(MVDR and cognitive-based MVDR beam formation)
    2012-08-04 17:31:53下载
    积分:1
  • CMI-DHB3-CMI
    在matlab中对AMI、HDB3、CMI等码进行编码,(In matlab encode for AMI)
    2013-12-13 23:32:24下载
    积分:1
  • ga-matlab-1.0
    algorithme génétique matlab algorithme génétique matlab algorithme génétique matlab
    2013-12-20 23:51:01下载
    积分:1
  • main
    关于计算在Klobuchar模型下的穿透点的电离层延迟和格网电离层延迟(Under Klobuchar model on the calculation of the penetration points ionospheric delay and grid ionospheric delay)
    2014-05-12 17:05:33下载
    积分:1
  • Floyd
    Floyd最短路算法的MATLAB程序,可以求解最短路问题,比如旅行商问题,(The most short circuit algorithm Floyd MATLAB procedures, can solve the most short circuit problems, such as traveling salesman problem, )
    2011-04-28 09:12:47下载
    积分:1
  • foldingLH
    Folding coefficient technique for DWT
    2011-08-06 16:25:07下载
    积分:1
  • MPSKTransmission
    有关MPSK调制,传输模型。成型脉冲分为矩形,升余弦脉冲,平方根升余弦脉冲。M的值为2,4和8.所加噪声是高斯白噪声。(Of the MPSK modulation, transmission model. Pulse shape is divided into rectangular, raised cosine pulse, the square root raised cosine pulse. The value of M for 2,4 and 8. The increase in noise is Gaussian white noise.)
    2009-05-21 12:33:22下载
    积分:1
  • medfilter
    基于matlab对图像进行中值滤波处理处理,另外附有自己编写的两种中值滤波算法,同时也可以使用matlab自带的median函数(median filter for image processing)
    2009-05-22 19:32:03下载
    积分:1
  • ICEE-574
    The model used for creating the reference voltage is shown in Fig. 4. First, photovoltaic output current (Ipv) and output voltage (Vpv) are passed through a first order low pass filter with a magnitude of G = 1 and a time constant of T = 0.01 seconds in order to filter out the high frequency components or harmonics from these signals as shown in Fig. 5 and Fig. 6. The filtered current and voltage signals (Ipv_F and Vpv_F) are then fed into the MPPT control block that uses the Incremental Conductance Tracking Algorithm. An algorithm that is based on the fact the slope of the PV array power curve shown in Fig. 7 is zero at the Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
    2013-07-23 17:54:09下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载