Kinect-Csharp

51单片机入门小程序，包括时钟、蜂鸣器、红外控制继电器和点阵显示。(51 single small entry procedures, including the clock, buzzer, IR control relays and dot matrix display.)

老板经常向我们灌输的一种51程序结构，可以说是很经典，基本能使用大部分MCU程序框架编写；(The boss often to instill a 51 program structure, is classic, basic procedural framework be able to use most of the MCU write )

基于ATMega64编写的BOOT升级程序，通过固定协议进行通讯，接收到的程序保存在外部Flash中，进行搬移(Based ATMega64 prepared BIOS upgrade program, through a fixed protocol for communication, received program stored in the external Flash, make the move)

采用MSP430微控制器作为主控制器，凌阳61单片机作为辅助，实现了在声音指令的控制下，完成一套流畅而优美的太极拳动作、激情而热烈的街舞动作等舞蹈动作(MSP430 microcontroller as the main controller, Sunplus 61 microcontroller as an auxiliary, the hip-hop movement under the control of the voice instructions to complete a smooth and graceful tai chi movements, passionate and enthusiastic dance moves)

说明：  led闪烁简单的c51入门程序代码，适合初学者入门的程序代码(LED flashes a simple entry procedures C51 code Suitable for beginners entry code )

八个发光二极管L1－L8分别接在单片机的P1.0－P1.7接口上，输出“0”时，发光二极管亮，开始时P1.0→P1.1→P1.2→P1.3→┅→P1.7→P1.6→┅→P1.0亮，重复循环。 (Eight light-emitting diodes L1-L8, respectively, then in the P1.0-P1.7 microcontroller interface, the output " 0" when the bright light-emitting diode, the beginning of P1.0 → P1.1 → P1.2 → P1. 3 → ┅ → P1.7 → P1.6 → ┅ → P1.0 Liang, repeat the cycle.)

该文档为IRMCF3xx的中文参考手册，对于使用这颗芯片的人来讲，这个资料非常珍贵。(The documentation for the IRMCF3xx the Chinese reference manual for the use of the chip of the people, this information is very valuable.)

锁相环源程序，基于stm32的控制，开发环境用keil5，(Phase locked loop source program, based on STM32 control, development environment with keil5,)

240128液晶初始化程序，调用子函数，有详细注释(240128 LCD initial program, call the son function, and have the detailed notes )

利用Keil C51 和LabVIEW编写程序实现PC与单片机串口通信。 设计任务 PC通过串行口将数字（00 ，01 ，02，03... ，FF，十六进制）发送给单片机，单片机收到 后回传这个数字，PC接收到回传数据后显示出来，若发送的数据和接收到的数据相等，则串 行通信正确，否则有错误。启始符是数字00，结束符是数字 FF。(Use Keil C51 and LabVIEW programming to achieve PC serial communication with microcontroller. Displayed after the PC via the serial port design task digital (00, 01, 02,03 ..., FF, hex) is sent to the microcontroller, the microcontroller receives return this figure, PC receives the return data , if the data sent and received data are equal, the serial communication is correct, otherwise an error. Startup character is a number 00, the end of the character is a number FF.)