-
局部变量用于自锁
说明: 自己编程的,局部变量用于自锁,用的是虚拟仪器编程软件!(Self-programmed, local variables for self-locking with labview.)
- 2019-06-09 16:31:01下载
- 积分:1
-
Lowpass-Filter
低通滤波器的labview模型,用于滤波消除系统的noise(low pass filter labview model)
- 2014-11-11 21:32:05下载
- 积分:1
-
YAV USB采集卡 VB例程
说明: 这是一个基于Labview的usb模拟量数据采集卡的例程源码,可用于二次开发(This is a routine source code of USB analog data acquisition card based on Labview, which can be used for secondary development.)
- 2020-06-17 11:40:02下载
- 积分:1
-
DataLogg
将需要保存的数据,保存在EXCEL文档或者TXT文档中。(save you need data for excel or txt file,in NI labview entironment.)
- 2014-03-11 09:02:23下载
- 积分:1
-
xtcd24dk_(jb51.net)
实现与周立功CAN板卡间通讯的上位机,内部有CAN波特率计算工具,完成基本通讯((Implementation and ZLG CAN communication between PC boards, internal CAN baud rate calculation tool, complete basic communication))
- 2018-03-23 08:59:09下载
- 积分:1
-
报表
说明: 报表程序,一个报表逐行写入表格的程序,可自定义写入。(Report program, a report written to the table line by line program, can be written to customize.)
- 2020-06-22 01:40:02下载
- 积分:1
-
LABVIEW与CAN
说明: labview can 通信 非常好用 建议大家收藏(labview can data transportion it is very nice)
- 2020-01-07 20:38:30下载
- 积分:1
-
AQUIR
对信号进行采集和保存,其采样率默认为信号频率的10倍,并将采集到的信号数据保存到电子表格中(Save signal data acquisition and preservation of the signal, the default sampling rate is 10 times the signal frequency, and collected into a spreadsheet)
- 2014-02-16 13:57:44下载
- 积分:1
-
标定训练原始图片与演示程序
说明: 基于LabVIEW的标定训练原始图片与演示程序(Calibration Training and Demonstration Program)
- 2019-04-18 10:18:47下载
- 积分:1
-
hanshuxinhaofashengqi
1.采用Labview设计一虚拟函数信号发生器, 通过数据采集卡输出波形信号,调节信号的相关参数,可观察示波器上波形的变化情况。
⑴ 以NI MyDAQ数据采集卡作为输出接口;
⑵ 数据采集卡输出多种信号,至少完成三种波形:正弦波、三角波、方波(可调占空比)的输出,同时前面板上显示各输出波形;
⑶ 频率、幅值、初相位、直流偏移量和方波的占空比(0~100 )等参数可以通过前面板控件调节。
⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes.
⑴ with NI MyDAQ data acquisition card as output interface
⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel
⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust.
⑷ output waveform can be displayed on the front panel.)
- 2015-04-25 18:26:52下载
- 积分:1