ID3

Matlab的OFDM在多径Rayleigh信道下的同步 1. 假设频率已同步，设计OFDM一种具体的采用循环前缀进行时间同步方法，用Simulink进行仿真，画出比特信噪比与捕获概率的关系曲线。 2. 设时间已同步，设计OFDM一种具体的采用循环前缀进行频率同步方法，用Simulink进行仿真，画出比特信噪比与频率同步误差的关系曲线.(Matlab-OFDM in multipath Rayleigh channel synchronization 1. Assume that the frequency has been synchronized, the design of a specific OFDM cyclic prefix for time synchronization method, using Simulink simulation to depict the bit signal to noise ratio and the capture probability curve. 2. Set up time is synchronized to design a specific OFDM cyclic prefix for frequency synchronization method, using Simulink simulation to depict the bit signal to noise ratio and frequency synchronization error of the curve.)

说明：  基于CRAFT的多阶段柔性设备布局优化算法 　　多阶段设备布局下的总成本包括设备拆装成本、物料搬运成本以及区域利用成本,问题的目标是最小化总成本。首先,在分析问题的基础上,建立基于多阶段设备布局优化目标的数学模型 其次,采用改进的CRAFT启发式算法优化单阶段设备布局 进一步,提出基于单阶段设备布局算法的多阶段启发式算法,优化多阶段设备布局 最后,数值实验表明算法优化后总成本降幅达28.57％. (CRAFT-based multi-stage flexible equipment layout optimization algorithm under the multi-stage equipment, the layout of the total cost including equipment disassembly cost, material handling costs as well as regional use of cost, the goal is to minimize the total cost. First of all, the analysis of the problem on the basis of the equipment based on the layout of multi-stage mathematical model of optimization objectives Secondly, the adoption of improved CRAFT heuristic algorithm to optimize the layout of single-stage device to further, based on equipment layout algorithm for single-stage multi-stage heuristic algorithm, optimize the layout of multi-stage equipment Finally, numerical experiments show that the optimized algorithm for the total cost of 28.57 percent decrease.)

标准粒子群优化算法1,采用MATLAB编写,本算法简单,易于实现,可调参数少,是非线性连续优化问题、组合优化问题(The standard particle swarm optimization algorithm 1,)

由设计要求可知，wp<=0.2π，允许误差幅度小于1dB，ws>=0.3π内衰减应大于15dB。为了验证数字滤波器的实际滤波功能，设计程序时，把输入序列定为验证函数x（t）=4sin（100πt）以及x（t）=4sin（200πt）和x（t）=4sin（400πt）。又因为Ts=1.25ms，T=80ms，故采样点为64，即N=64，所以当M=6，可以同时调试并验证程序的滤波功能。(Seen by the design requirements, wp < = 0.2π, allow a margin of error of less than 1dB, ws> = 0.3π within attenuation greater than 15dB. In order to verify the actual filtering function of the digital filter design program, the input sequence as validation function x (t) = 4sin (100πt) and x (t) = 4sin (200πt) and x (t) = 4sin (400πt) . And because Ts = 1.25ms, T = 80ms, so the sampling points is 64, that is N = 64, so when M = 6, can debug and validate filtering program.)

双层规划模型的遗传算法求解的Matlab源码(GA for Bilevel Programming Model with Matlab)

蓄电池simulink模型 适合做蓄电池在matlab中建模参考学习(battery simulink model)

Implemtenacion de estructura FIFO

用于分类的matlab工具箱，供大家学习交流(Matlab toolbox for classification ，We can exchange advices with it.)

calculation of load flow in power system using matlab power engineering field

对不理想环境下信号DOA（Ｃａｐｏｎ算法）的性能仿真分析。在小角度时ｃａｐｏｎ算法性能分析。(Not an ideal environment for the signal DOA (Capon algorithm) of the performance simulation. In the small angle capon algorithm performance analysis.)