abctorlc

给大家传了一份精通matlab6.5教程 我开始学习的时候就在看这个 希望对大家有帮助(a file about matlab 6.5)

说明：  logistic回归分析学习的SAS实验资料2(Learning SAS logistic regression analysis of experimental data 2)

用Matlab作图时，特别是所作的图是要用于科研论文投稿时，对图的大小有一定要求。但用缺省设置作图时，图的大小不能控制，而且常常有大块的空白。本程序可控制图的大小和位置，并能自动去掉空白。(Using Matlab mapping, especially of the map is to be used for scientific research papers submission, the size of the map has a certain requirement. However, when using default settings mapping, map the size of control, often have large gaps. This procedure can control the map size and position, and can automatically remove blank.)

协作分集信道容量的研究英文的，给出了不同情况下的模型()

说明：  根据前人研究成果可以证明，煤镜质组反射率各向异性对煤田构造特征具有指示意义，镜质组最小反射率可以指示构造主应力方向。然而，在实际测量中，如何得到真正的镜质组最大、最小反射率及其方位是其中的关键环节。利用现有的岩石有限应变椭球拟合方法进行镜质组反射率椭球体拟合不失为一种行之有效的方法，可以由此确定镜质组最大、最小、中间反射率及其三维空间方位。 将之前拟合得到的反射率椭圆看作岩石有限应变椭圆即二维应变，其由之前的统计方法测定得到，三个截面的数据对于拟合唯一应变椭球来说是过多的，因此不可避免出现误差，导致三个截面应变椭圆不通过同一个椭球的情况。为了从三个截面数据得到唯一的应变椭球，需要对得到的数据进行相容性调整。采用Oertel的方法，从每一测量参数在不同截面中的值是正态分布这一假定出发，利用加权最小二乘法进行误差调整。(According to results of previous studies may prove vitrinite reflectance anisotropy on structural characteristics have implications for coal, vitrinite reflectance may indicate tectonic minimum principal stress directions. However, in actual measurement, how to get real vitrinite maximum, minimum reflectivity and its orientation is the key link. Conduct vitrinite reflectance ellipsoid fitting regarded as a proven method using existing rock finite strain ellipsoid fitting method can thus determine vitrinite maximum, minimum, intermediate reflectance and dimensional spatial orientation . Before fitting the reflectance of finite strain ellipse oval rock that is seen as a two-dimensional strain, as determined by statistical methods which have been before the data fit only for the three sections of the strain ellipsoid is excessive, and therefore can not to avoid errors, resulting in three elliptical cross-section does not pass through the same strain ellipsoid situation. In order to obtai)

VAD Voice Activity Detection

优化程序，包括最短路径，最小生成树等。具体说明可以参考content文件 (optimization procedures, including the shortest path, minimum spanning tree, and so on. Specify reference document content)

单频网的链路级Matlab仿真程序,直接运行可得到误符号率。(Link level simulator for single carrier networks,The simulator outputs symbol error rate.)

CDMA系统仿真,非常好的东西哦，希望大家赶快下载吧(CDMA system simulation)

提取指纹特征点的matlab代码，很有用，利用自适应阈值进行分割，再进行频域增强，根据八邻域纹线编码进行特征提取。(Extracted fingerprint feature points of the matlab code, useful, adaptive threshold segmentation, and then increased in frequency domain, the eight neighborhood ridge coding for feature extraction.)