登录
首页 » matlab » anisodiff2D

anisodiff2D

于 2011-11-19 发布 文件大小:2KB
0 265
下载积分: 1 下载次数: 30

代码说明:

  matlab anisodiff各向异性滤波算法(matlab anisodiff anisotropic filtering algorithm)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • model_rasteniy_nasekomyh.pdf
    Rus Mastering 3D Graphics Digital Botany and Creepy Insects Bill Fleming WILEY COMPUTER PUBLISHING DMK Press 2002
    2010-07-19 18:16:33下载
    积分:1
  • heart_rate_qrs_detect
    ECG QRS DETECTION( HEART BEAT IN ONE MINUTE 心率检测版权属于D.K. Ravish Bangre (ECG QRS DETECTION( HEART BEAT IN ONE MINUTE by D.K. Ravish Bangre )
    2011-07-20 23:29:56下载
    积分:1
  • myhilbert
    本程序用于线性调频信号频率的测量,首先产生一加噪线性调频信号,再使用小波滤波去除噪声,最后使用希尔伯特变换法求信号的频率。(This procedure is used to measure the frequency of chirp signal, first generate a chirp signal with noise, and then use wavelet filtering to remove noise, and finally use the Hilbert transform method for the signal frequency.)
    2011-09-02 10:18:57下载
    积分:1
  • Rt_max
    雷达最大探测距离,包括雷达参数,雷达最大探测距离的计算公式。(calculation of radar maximal detect distance)
    2020-06-30 23:00:02下载
    积分:1
  • smth
    MATLAB SIMULINK 改进型SIMITH预估控制器(MATLAB SIMULINK improved SIMITH forecast controller)
    2014-01-17 10:25:50下载
    积分:1
  • qsyn10
    matlab下用于稳定系统设计的库文件,可以作为辅助设计系统的软件使用(Qsyn the Toolbox for Robust Control Systems Design for use with Matlab)
    2013-11-14 18:41:58下载
    积分:1
  • grjufyyn
    粒子图像分割及匹配均为自行编制的子例程,PLEsBZv参数matlab程序运行时导入数据文件作为输入参数,BP神经网络用于函数拟合与模式识别,有较好的参考价值,xICYlkW条件DC-DC部分采用定功率单环控制,均值便宜跟踪的示例。( Particle image segmentation and matching subroutines themselves are prepared, PLEsBZv parameter Import data files as input parameters matlab program is running, BP neural network function fitting and pattern recognition, There are good reference value, xICYlkW condition DC-DC power single-part set-loop control, Example tracking mean cheap.)
    2016-02-19 23:10:07下载
    积分:1
  • Generic
    Generic OFDM with Cyclic Prefixing
    2010-08-10 20:04:07下载
    积分:1
  • HY4145
    HYCON HY4145 Battery Fuel Gauge Demo For Arduino
    2016-12-14 22:23:04下载
    积分:1
  • S4
    说明:  function [ret,x0,str,ts,xts]=s4(t,x,u,flag) s4 is the M-file description of the SIMULINK system named s4. The block-diagram can be displayed by typing: s4. SYS=s4(T,X,U,FLAG) returns depending on FLAG certain system values given time point, T, current state vector, X, and input vector, U. FLAG is used to indicate the type of output to be returned in SYS.
    2010-03-03 17:16:43下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载