Interpolation-in-Digital-Modems

说明：  bpsk调制仿真，可直接用 1、数字调制方法 数字调制就是把数字基带信号的频谱搬移到高频处，形成适合在信道中传输的带通信号。基本的数字调制方式有振幅键控（ASK）、频移键控（FSK）、绝对相移键控（PSK）、相对（差分）相移键控（DPSK）。在接收端可以采用想干解调或非相干解调还原数字基带信号。 数字信号的传输方式分为基带传输和带通传输。然而，实际中的大多数信道（如）无线信道具有丰富的低频分量。为了使数字信号在带通信道中传输，必须用数字基带信号对载波进行调制，以使信号与信道的特性相匹配。(1, digital modulation method Digital modulation is the transfer of the spectrum of a digital baseband signal to a high frequency to form a bandpass signal suitable for transmission in the channel. The basic digital modulation methods are amplitude keying (ASK), frequency shift keying (FSK), absolute phase shift keying (PSK), and relative (differential) phase shift keying (DPSK). At the receiving end, the digital baseband signal can be restored by using dry demodulation or non-coherent demodulation. Digital signal transmission methods are divided into baseband transmission and bandpass transmission. However, most channels in practice, such as wireless channels, have rich low frequency components. In order for a digital signal to be transmitted in a band channel, the carrier must be modulated with a digital baseband signal to match the signal to the characteristics of the channel.)

说明：  雷达信号分选的经典matlab代码。包含PRI变换、CDIF、SDIF三种方式(radar signal sort include PRI CDIF SDIF)

说明：  基于SimuLink的数字通信链路仿真 包含QPSK及16QAM模式下的链路计算(Simulation of digital communication link based on Simulink Including link calculation in QPSK and 16QAM mode)

支持IEC60870-5-104: 2000 IEC104规约软件包 实现104规约主站侧链路层的功能(IEC_Master_104.lib: void Init_SockServerport(WORD port=2404) void Init_Linkpara(int t0=30,int t1=15,int t2=10,int t3=20,int k=12,int w=8) virtual void On_init_Link_process() virtual void On_init_Sock_process() virtual void On_ErrorMsg(char*msgbuf) void slave_start() void slave_close() )

这个是阵列信号处理的资料，学习信号处理的朋友或者是做天线的朋友，可以下载此资料，尤其对写论文（天线理论方面）的战友有很多实用意义。(singnal proicessing resource.i do not like write english, but for value, i trying)

研究d2d通信加中继节点来优化蜂窝小区边缘用户通信，并通过MATLAB仿真(The D2D communication and relay nodes are studied to optimize the edge user communication of cellular cell, and the simulation is carried out by MATLAB.)

采用加权网络中节点强度和权重都是幂率分布的模型，GPS和INS组合导航程序，做视觉测量的上位机代码。( Using weighted model nodes in the network strength and weight are power law distribution, GPS and INS navigation program, Do Vision Measurement PC code.)

本文分析了多级维纳滤波器的特性，在加性噪声和二维天线阵列如均匀圆阵、均匀面阵、十字阵等条件和背景下，对信源个数和信源参数估计问题进行了研究，提出了基于多级维纳滤波器前向分解特性的快速参数估计方法，同时提出了基于多级维纳滤波器的二维ESPRIT参数估计方法，该类方法无需协方差矩阵的估计运算及分解运算，计算复杂度较低。另外，还提出了对信源个数的估计算法。(This paper analyzes the characteristics of multistage Wiener filter, in the additive noise and the two-dimensional antenna array such as a uniform circular array, the uniform array, cross array conditions and background, the source number and source parameter estimation problem undertook study, put forward based on Multistage Wiener filter prior to the decomposition characteristics of fast parameter estimation method, at the same time based on Multistage Wiener filter 2D ESPRIT parameter estimation method, the method does not need to estimate of covariance matrix calculation and decomposition, relatively low computational complexity. In addition, also put forward for source number estimation algorithm.)

说明：  matlab code for maximal se master

cdma系统 LMS算法 盲自适应多用户检测(cdma systems LMS adaptive multiuser detection algorithm)