ConsoleApplication3

光电编码器，是一种通过光电转换将输出轴上的机械几何位移量转换成脉冲或数字量的传感器。 这是目前应用最多的传感器，光电编码器是由光栅盘和光电检测装置组成。光栅盘是在一定直径的圆板上等分地开通若干个长方形孔。由于光电码盘与电动机同轴，电动机旋转时，光栅盘与电动机同速旋转，经发光二极管等电子元件组成的检测装置检测输出若干脉冲信号(Photoelectric encoder, a photoelectric conversion to the output shaft of the mechanical geometry of displacement into a pulse or digital sensors. This is currently the most widely used sensors, optical encoder is determined by the grating disk and photoelectric detection device component. Grating disc is a circular plate in such a diameter of several rectangular holes partially opened. Because coaxial photoelectric encoder and the motor, the motor rotates, the grating disk rotates with the same speed motor, the light-emitting diodes and other electronic components of the detection device detects certain pulse signal output)

说明：  多路稳压电源的设计资料 包括电路图 论文 (The describe of muitiply source)

IIC总线协议芯片CH452驱动代码，配合数码管和按键，适合快速移植。(IIC bus agreement CH452 chip driver code, with digital tube and buttons, suitable for rapid transplantation. )

泛型例题源代码，个人编写，可以提供给初学者参考参考(A generic sample source code, individual writing, can provide reference for beginners reference )

单片机学习 红外遥控编码详细资料 34页 (Infrared remote control encoded data)

基于pic16f676 EEPROM的问题 用软件仿真没问题，但烧到片子里，不能正常运行。情况是这样的：假如循环向EEPROM中写数据，9，8，7，6，5，4，3，2，1，然后读，发现每一位读出的都一样，是写循环中第一个写进去的字节，也就是9。其他的并没有写进去。 EEPROM的写通过判断标志位就可以，但是在下一次写之前要清除上一次写完成的标志位。也就是说，每次写完要清除完成标志位，否则下一次写不进去。(Based on pic16f676 EEPROM problem With the software simulation no problem, but burn to film, not normal operation. The fact of the matter is: if cycle to write the data of EEPROM, 9,8,7,6,5,4,3,2,1, then read, and found that each of the read, write the first cycle is written in bytes, also is 9. The other are not written in. Write through the judgement of EEPROM sign a can, but in the next write to remove the last completed before writing the sign of a. That is, every time to remove the written finish marks a, or the next write in. )

89c51时钟，通过液晶屏显示 还可以通过按键设置时间(89C51 clock, through LCD screen display, you can also set time by key.)

一个I2C模式下的例程，熟练使用I2C进行通讯(A I2C mode routine, skilled use of I2C for communication.)

该程序主要用来测量信号的脉冲宽度，具有较好的稳定性和精度。(The program is mainly used for the measurement of pulse width signal,and has good stability and accuracy. )

说明：  在个是AVR的PDF介绍，内容很详细，也很好，特别适合初学者入门的学习(Here is the introduction of PDF of AVR, which is very detailed and very good. It is especially suitable for beginners to learn.)