登录
首页 » matlab » MAngxindaoguji

MAngxindaoguji

于 2014-12-07 发布 文件大小:6KB
0 275
下载积分: 1 下载次数: 13

代码说明:

  matlab编写的盲信道估计程序,对进行信道估计的朋友有用(Blind channel estimation matlab program written for channel estimation useful friends)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • BGA
    This is a program for Binary Genetic Algorithm
    2010-02-10 23:55:06下载
    积分:1
  • linsweep35M
    利用matlab产生线性调频信号,主要用于雷达信号的产生。(matlab create Radar signal waveform)
    2009-06-30 21:28:02下载
    积分:1
  • fuzzpid
    PID模糊控制程序,附带simulink仿真图形(PID fuzzy control procedures)
    2014-01-16 19:58:45下载
    积分:1
  • matlab-draw-examples
    matlab draw examples
    2013-10-13 11:08:25下载
    积分:1
  • matlab-installer-ways
    matlab安装方法和序列号,值得拥有.免得大家去找了,可以参考( matlab installer ways and license)
    2013-11-22 16:35:59下载
    积分:1
  • MY_CSTR
    该模块是通过simulink中的s函数来建立的CSTR模型,能够用于故障诊断。(The module is by CSTR the simulink s function to create the model can be used for fault diagnosis.)
    2012-12-12 14:02:37下载
    积分:1
  • taeniwci
    微分方程组数值解方法,IDW距离反比加权方法,数据模型归一化,模态振动,isodata 迭代自组织的数据分析,研究生时的现代信号处理的作业,是路径规划的实用方法。(Numerical solution of differential equations method, IDW inverse distance weighting method, Normalized data model, modal vibration, Isodata iterative self-organizing data analysis, Modern signal processing jobs when the graduate, Is a practical method of path planning.)
    2016-03-12 00:47:10下载
    积分:1
  • 项目4
    说明:  任务:设计一个4×2.5Gbit/s 长距离光纤传输系统,并利用OptiSystem 仿真验证。 要求: 1.采用波分复用技术,波长设置以100GHz 为间隔,频率分别为193.1THz、193.2THz、193.3THz、193.4THz,每个波长传输速率为2.5Gbit/s(NRZ),传输距离为300km。采用常规光纤,光纤损耗系数为0.25dB/km。 2.单通道光发送机最大输出功率为0dBm,光接收机的接收光功率不低于-26dBm,过载点为-10dBm。 3.可以采用EDFA 作为线路放大器,其中EDFA 的输入功率限制在-18~2dBm,最大输出功率20dBm,增益范围为13~25dB,噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
    2019-05-13 09:39:41下载
    积分:1
  • OpenTSTOOL_win
    时间系列非线线性处理工具包,可以计算多数非线性参数,例如:李亚谱诺夫指数,相关维等(nonlinear parameter toolkit)
    2010-01-20 09:53:45下载
    积分:1
  • mbook
    说明:  matlab 的最好的一本教科书,北航张志涌(matlab one of the best textbooks, BUAA Zhang Yong)
    2008-09-25 23:59:42下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载