matlab-in-mathematical-equations

对机侧系统的仿真包括系统模型的搭建、化简和控制算法的设计。直驱式永磁同步风力发电系统的机侧模型包括风力机模型、永磁同步电机模型和机侧PWM变换器模型。永磁同步电机和机侧PWM变换器模型的数学模型可以化简在一个数学方程中，简化方框图的搭建。控制器的设计目标是控制同步电机的转速实现最大风能的跟踪。(Simulation of the machine side of the system, including structures, simplification and control algorithms designed system model. Direct-drive-side model of permanent magnet synchronous wind power generation system includes a wind turbine model, permanent magnet synchronous motor model and machine-side PWM converter model. Mathematical model of permanent magnet synchronous motors and machine-side PWM converter model can be simplified in a mathematical equation, a simplified block diagram of the building. The controller is designed to control the synchronous motor speed to achieve maximum wind power tracking.)

knn-K近邻法实现两分类的函数代码，输入为两类的样本特征，和待测试的样本向量，输出为分类结果。(knn-K nearest neighbor method to achieve the two categories of function code, enter the characteristics of two types of samples, and samples to be tested vector, the output for the classification.)

C均值源代码的MATLAB编程，源代码，但是有点点复杂(C means the source code of MATLAB programming, source code, but there is little complexity)

说明：  《matlab语言常用算法程序集》源代码 第五章(&quot Matlab common algorithms assembly language&quot source code Chapter)

matlab运行的lsb隐写算法，附带实验报告，lsbget.m,lsbhide.m,jpgand.m(matlab running lsb steganography, with lab reports, lsbget.m, lsbhide.m, jpgand.m)

说明：  车厢调度:程序对栈的任何存取（即更改，读取和状态判别等操作必须借助于基本操作。(Train scheduling: proceedings of the stack of any access (that is, changing, reading and state identification must be by means of basic operations such as Operation.)

用鼠标画线，运行程序后，可以在axis界面上画任意曲线，且每个点的地址会返回到matlab主窗口(draw a line with a mouse)

说明：  升压转换器是一种DC / DC电源转换器，可将电压从其输入（源）升至其输出（负载）。在连续导通模式下（流经电感的电流永远不会降为零），升压转换器的理论传递函数为： 占空比在哪里0.5 在此示例中，转换器从250 V电源馈送RC负载，并且PWM频率设置为31 kHz。 模拟 运行仿真并观察示波器上的波形。确认负载电压（Vout）的平均值非常接近理论值：Vout = 250 /（1- 0.5）= 500V。(A boost converter is a DC/DC power converter which steps up voltage from its input (source) to its output (load). In continuous conduction mode (current through the inductor never falls to zero), the theoretical transfer function of the boost converter is: where is the duty cycle.0.5 In this example, the converter is feeding an RC load from a 250 V source and the PWM frequency is set to 31 kHz. Simulation Run the simulation and observe waveforms on Scope. Verify that the mean value of the load voltage (Vout) is very close to the theoretical value of: Vout = 250 / (1 - 0.5) = 500 V.)

该程序是实现OFDM在频带上的运用，挺好用的(The program is to achieve the use of OFDM in the band, very good use)

本程序是基于LeventCode平台作的。 ---包括以下方法： BivaShrink方法、模型1、模型2、模型3（TrivaShrink方法）、BayesShrink方法、LAWMLShrink方法的DWT实现和DT_CWT实现。(This procedure is based on the LeventCode platform for the. --- Including the following methods: BivaShrink method, model 1, model 2, model 3 (TrivaShrink method), BayesShrink method, LAWMLShrink method of DWT implementation and DT_CWT achieve.)