SPH

基于STM32的双串口通信程序，能实现两个串口的收发，程序默认采用串口2接收数据，串口1发送(Based on the STM32 dual serial communication procedures, can achieve two serial transceivers, the program defaults to the serial port 2 receives the data, send the serial port 1)

finger 103 for fingerscan

利用easyx写的矩阵键盘仿真，希望可以给爱好者提供参考。(Use easyx wrote matrix keyboard emulation, hoping to provide a reference for enthusiasts.)

超声波测距，在51单片机内核下的超声波测距程序，比较精简，希望大家受用。(Ultrasonic ranging, in 51 single kernel of ultrasonic distance measurement procedures, more streamlining, I hope everyone is good enough.)

说明：  基于MODBUS协议的单片机通信系统，上位机+下位机(MODBUS Protocol-based communication system microcontroller)

自动交通控制系统用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁示线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示）(Automatic traffic control system using red, green, yellow light-emitting diodes, said a total of three traffic lights, the use of single-chip analog time display on a regular traffic signal control and management. Changes of lights to be as follows: 1) Release Line: green clearance 25 seconds, the yellow light warning for 5 seconds, then the red light is prohibited. 2) ban shows lines: the red light is prohibited for 30 seconds, then the green light to release. 3) When the red light in one direction, if the direction of the car through, the alarm speaker sound. (Hit the red signal available 3-5V analog representation))

双馈风电机组的PSCAD模型，是通用模型，有助于帮助解决双馈风电机组建模问题(PSCAD doubly-fed motor model)

基于AT89C51单片机的出租车计价器的程序设计(AT89C51 microcontroller Taximeter-based program design)

xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1－启动与停止步进电机运行 K2－设定步进电机运行圈数 （1-20圈） K3－设定步进电机转动方向 K4－设定步进电机运行速度 步进电机的转速控制分16档，数字越小，转速越快。 7.5度步进电机；周期7.5×4=30度，电机转动一圈需12个周期 资源：p1.0-p1.3接反向器74ls14，输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口按键：lcd1602插入实验仪(xl Series Singlechip Experiment LCD1602 demo program shows the direction of stepper motor speed controller circle shows the number of adjustable LCD1602 direction stepper motor controller lap speed of a few adjustable K1-start and stop the stepper motor running K2-setting step motor running a few laps (1-20 laps) K3-set stepper motor rotation direction of K4-setting speed of stepper motor stepper motor speed control minutes 16 stalls, the number of smaller, faster the speed. 7.5 degree stepper motor cycle of 7.5 × 4 = 30 degrees, rotating electric lap 12 cycles required resources: p1.0-p1.3 then reverse browser 74ls14, followed by stepper motor output p3.7 then provide a small speaker key tone, p1.4-p1.7 port access keys: lcd1602 insert Tester)

Cambios de giro de un motor DC controlado por hiperterminal