LED-PAR64S-COB-200WW-LMP

MDK RTX51 开发51单片机，使用RTX，对于初始学者很方便(MDK RTX51 )

AGV自动导引小车程序，采用51单片机作为主控芯片，包括测速程序、PID调速程序等等。(AGV autopilot, using 51 SCM car program as main control chip, including velocimetry procedures, PID speed control procedures, etc. )

25F040 C PROGRAM,25F040 C PROGRAM,25F040 C PROGRAM(USEFUL 25F040 C PROGRAM,25F040 C PROGRAM,25F040 C PROGRAM,25F040 C PROGRAM,25F040 C PROGRAM)

光伏微网逆变器设计手册，从光伏板特性分析到DCDC反激升压再到DCAC逆变最后到锁相环检测并网都详细说明。(PV micro-inverter design manual, from the characteristics of photovoltaic panels to boost DCDC flyback DCAC inverter then finally to the phase-locked loop detection and network are described in detail.)

单片机C语言程序设计实训100例——基于8051+Proteus仿真(1(Microcontroller C Programming Language Training 100 cases- based on 8051+ Proteus simulation (a)

详细介绍了利用PADS 9.5 实现原理图与PCB设计的方法和技巧。配合大量示意图，介绍了印制电路板设计流程和常用电路模块的PCB处理方法(The method and technique of using PADS 9.5 to realize schematic diagram and PCB design are introduced in detail. With a large number of schematic diagrams, the design process of printed circuit boards and the PCB processing methods of common circuit modules are introduced)

this is 8051 microcontroller timer code

STM8S105 实现多路的ADC采集，并且把其中的两路通过串口UART发送到电脑上。其中有通信方法RS232 说明和LabVIEW2010的上位机示波器。oscillograph(STM8S105 LabVIEW2010 UART RS232 oscillograph ADC Send.)

P1口扩展实验 P1口既做输入口又做输出口，KEY1做为左转弯开关，KEY2做为右转弯开关。LED5、LED6做为左转弯灯，LED7、LED8做为右转弯灯（如图2-2）。 编程实现汽车转向灯功能，即：KEY1接高电平KEY2接低电平时，右转弯灯灭，左转弯灯以一定频率闪烁（注意：KEY拨向上方为0）；KEY2接高电平KEY1接低电平时，左转弯灯灭，右转弯灯以一定频率闪烁；KEY1、KEY2同时接低电平时，发光二极管全灭；KEY1、KEY2同时接高电平时，发光二极管全亮。(P1 I extended not only to do experiments P1 I also do input output, KEY1 switch as a left turn, KEY2 as switches and turn right. LED5, LED6 as a left turn lights, LED7, LED8 as lights and turn right (Figure 2-2). Programming car turn signal function, namely: KEY1 high key2 access low-level access, the right turn lights out, left turn to a certain frequency of flashing lights (Note: KEY allocated to the top to 0) KEY2 access high Key1 low-level access, the left turn lights out, turn right to a certain frequency of flashing lights KEY1, KEY2 low at the same time, the light-emitting diode body KEY1, KEY2 high at the same time, the light-emitting diode light-wide.)

说明：  it`s a examples about Keil