LabView-lesson

说明：  使用工具说明，EDA工具的DataSheet，简单介绍及相关文档(Tool Description, Data Sheet of EDA Tool, Brief Introduction and Related Reference Documents)

用于智能体自动目标搜索或自动避障路径规划(Path Planning for Agent Automatic Target Search or Obstacle Avoidance)

Linux下SPI转USB驱动，基于沁恒ch374芯片(Linux SPI USB driver based on ch374 chip)

说明：  cascaded 12 level converter(cascaded 12 level converter dv)

说明：  1. 硬件接线 （1）调试串口(UART_Debug)使用UART2，在“printf.h”文件中宏定义， 对应引脚为TX-PTD7，RX-PTD6 （在“uart.h文件中宏定义）。 （2）灯0~3（LIGHT_0~LIGHT_3）对应的引脚是PTC0~PTC3，高电平点亮（由硬件接法决定） （3）SPI0_CLK对应的引脚是PTE0， SPI0_MOSI对应的引脚是PTE1， SPI0_MISO对应的引脚是PTE2，SPI0_PCS对应的引脚是PTE3， SPI1_CLK对应的引脚是PTG4， SPI1_MOSI对应的引脚是PTG5， SPI1_MISO对应的引脚是PTG6，SPI1_PCS对应的引脚是PTG7。 （4）SPI0作为master,SPI1作为slave，SPI1接收SPI0发送的数据并产生中断。 用导线将PTE0与PTG4对接，将PTE1与PTG5对接，将PTE2与PTG6对接，将PTE3与PTG7对接。(1. Hardware wiring (1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6. (macro definition in the uart.h file). (2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection. (3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1. The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3. The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5. The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7. (4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption. PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)

说明：  计算齿轮刚度时变刚度值，用于齿轮动力学分析(Calculating the time-varying stiffness of gear for gear dynamic analysis)

说明：  码头调度中船舶进港时的泊位分配问题，利用遗传算法matlab进行求解(Berth allocation problem of ships entering port in wharf dispatching)

向滑动幻灯片是一款带箭头按钮跟数字标签的jquery滑块幻灯片(A sliding slide is a jQuery slider slide with arrow buttons and digital labels.)

Grid 控件应该分成自由式 报表和数据相关表格两种，其内部实现机理不尽相同，你说的要求恰恰要把这两种风格的 报表融合起来：Exel 是典型的自由式报表，复制、拖拉、合并单元格等，它的每个单元格 都是相对独立的，数据相关表格就很不一样了，最典型的就是它有数据列的概念。 -Grid Control Report should be divided into freestyle and data related to table two, the internal mechanism of implementation is different, you said it to the requirements of these two styles together Report: Exel is a typical freestyle Report, copy, drag and drop, merger cells and so on, each of its cells are relatively independent, data related to very different on the table, the most typical is that it has the concept of data columns.

说明：  二阶锁相环simulink仿真，可以看一看(Second-order PLL Simulink simulation, you can see)