STATCOM--main-circuit-device-design

LLC经典资料，学习LLC基础，详细分析LLC设计原理(LLC basic dsp matlab )

UCOSII在mcs12dg128上的移植，有包括初始化任务，红绿灯，互斥信号量，建立统计任务，空闲任务，任务额外信息，消息队列在内的6个工程。内容十分详尽，适合UCOS的学习。不过因为文件过多，低license无法编译，请自行申请license(UCOSII at mcs12dg128 on the transplant, including initialization tasks, the traffic lights, mutual exclusion semaphores, set up statistical mission, free mission, tasks, additional information, message queues, including six works. Very detailed study of the fit uCOS. However, because file too large, low-license can not compile your own application for license)

说明：  适用于EMWIN5.42版本的中文用户手册(EMWIN version 5.42 user manual in Chinese)

AD9851中文资料，为pdf格式，资料比较详细，希望对需要者有所帮助。(AD9851 Chinese data)

赛普拉斯单片机的C语言开发说明，比较适合于刚刚入门的工程师(Cypress MCU C language development that are more suitable for the engineer just started)

old gpio interface to other kernel modules don t use in new code, will go away in 2.7 have a look at bttv-gpio.c instead.

该防盗系统使用热释电红外传感器作为人体探测模块，并将防盗系统设计为两个用户可选择的模式：在家模式和离家模式，当处于在家模式时，如果传感器检测到有人进入监控范围，则自动响起门铃提醒用户有访客，就不会发生误把访客当作盗贼的报警事件了；当处于离家模式时，如果传感器检测到有人进入检测范围，则开启声光报警模块进行报警。同时，该系统为密码控制系统，用户通过输入正确密码才可改变模式和解除警报，这也增强了该系统使用的可靠性。(The anti-theft system using pyroelectric infrared sensor as the detection module, and alarm system design for the two user selectable mode: home mode and home mode, when in the home mode, if the sensor detects a person into the monitoring range, will automatically alert the user to a visitor rang the doorbell, will not happen take the visitor as an alarm event of thieves; when in the home mode, if the sensor detects a person into the detection range, open alarm alarm module. At the same time, the system is a password control system that allows users to change their mode and lift their alarms by typing in the correct password, which increases the reliability of the system.)

stm32f401使用ad模块pcf8591(using pcf8591 by the stm32f401)

国产arm芯片MM32F103的CoreMark跑分，实际测试过，在keil5上实现(MM32F103 CoreMark)

本系统是基于STM32F103RBT6微控制器所设计的温度测量系统，通过温度芯片传感器 DS18B20 测量温度，微控制器驱动液晶模块显示当前测得的温度。该测温系统应用测温传感器DS18B20.通过DS18B20把温度值转换成数字量，把数字量送给微处理器，并在液晶显示器上显示出来(This system is based on the temperature measurement system designed by the STM32F103RBT6 micro controller. The temperature is measured by the temperature chip sensor DS18B20, and the micro controller drives the liquid crystal module to display the current temperature. The temperature measurement sensor DS18B20. converts the temperature value into the digital quantity by DS18B20 and sends the digital to the microprocessor and displays it on the liquid crystal display.)