CS_OMP

摘　要:根据HFC网络上行信道的特性,建立了信道模型 分析了上行信道中存在的各种噪声对QPSK 调制技术的影响。结果表明在C /N (传输信道载噪比)较低的情况下,采用QPSK调制方式,可以提高系 统的抗干扰能力。 关键词: QPSK 光纤同轴电缆混合网 上行信道 噪声(Abstract: HFC network in accordance with the characteristics of the uplink channel, the establishment of a channel model an analysis of the various uplink channel noise on the impact of QPSK modulation. The results show that the C/N (transmission channel carrier-to-noise ratio) lower, the use of QPSK modulation, can improve the system of anti-interference ability. Keywords: QPSK hybrid fiber coaxial cable network uplink channel noise)

此算法描写了如何选择初始轮廓的位置，以及怎样控制初始轮廓的演化。(This algorithm describes how to select the location of the initial profile, and how to control the evolution of the initial contour.)

先进PID控制matlab仿真，对PID的仿真有很大帮助，内含好多源代码(Advanced PID control matlab simulation , PID simulation , containing a lot of source code )

基于模型的风力发电机资料，有需要的学习一下吧(Model-based wind turbine data, there is a need to learn about it)

A basic example of piano in Matlab

hi this is the code for svd in ieee 14 bus system

Reservoir Optimization with PSO

MATLAB 牛顿下山法的一个小程序，原理就不详细说了。因牛顿迭代法受初值选取的限制，为防止迭代发散，对迭代过程再附加一项要求:|f(x(k+1))|<|f(x(k))|,将牛顿法迭代的结果:x(k+1) =x(k)-f(x(k))/f (x(k))和前一近似值x(k)适当加权平均做为新的改进值:x(k+1)=u*x(k+1) +(1-u)*x(k),其中u(0<> 迭代时u取1开始，逐次减半计算，直至附加要求符合为止。实例计算中x(k)=x(0)不变，只更新u和x(k+1)，直至:|f(x(k+1))|<|f(x(k))|（即|f(x(1))|<|f(x(0))|)，然后更新下山因子为u=1,继续以牛顿法迭代。(MATLAB Newton-down a small program, the principle is not explained in detail. Newton iteration by the initial value of the selected limit, in order to prevent additional iterative divergence, the iterative process a request: | f (x (k+1)) | < | f (x (k)) | Newton iteration Results: x (k+1) ' = X (k)-f (x (k))/f' (x (k)) and a previous approximation x (k), appropriately weighted average as a new improved value: x (k+1 ) = u* x (k+1) ' + (1-u)* x (k), where u (0 < u> iteration take successive calculated at 50 until the additional requirements found so far. examples of calculation of X ( k) = x (0) unchanged profile u and x (k+1, hungry) until: | f (x (k+1)) | < | f (x (k)) | (i.e. | f (x (1)) | < | f (x (0)) |), then profile downhill factor for u = 1, to continue to Newton iteration.)

simulation dfig in matlab

说明：  层次分析法matlab程序及说明书，是指将与决策总是有关的元素分解成目标、准则、方案等层次，在此基础之上进行定性和定量分析的决策方法。(Analytic hierarchy process (AHP) matlab program and specification is a decision-making method that decomposes the elements related to decision-making into objectives, criteria, schemes and other levels, and carries out qualitative and quantitative analysis on this basis.)