登录
首页 » matlab » wKA

wKA

于 2021-03-12 发布 文件大小:4KB
0 281
下载积分: 1 下载次数: 281

代码说明:

  ωKA是实现SAR图像成像的一种方法,该程序实现了ωKA的近似和精确两种成像方式,仿真参数参考《合成孔径雷达成像——算法与实现》,利用Stolt插值实现了目标成像,最后在方位向和距离向进行切片,观察成像结果。(ωKA is one of the point target imaging algorithms of SAR . This program implements both exact and approximate ways of imaging. Simulation parameters refer to the book Synthetic Aperture Radar imaging- Algorithms and Implementation .)

文件列表:

wKA
...\ftx.m,191,2013-11-11
...\fty.m,196,2013-11-11
...\iftx.m,193,2013-11-11
...\ifty.m,198,2013-11-11
...\wKA_accurate.m,3082,2014-11-19
...\wKA_approximate.m,3021,2014-10-22

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • MotionDetection
    Motion Detection Code in Matlab
    2009-12-19 06:18:40下载
    积分:1
  • KSVD_Matlab_ToolBox
    图像稀疏编码的一种方法,可用于基于稀疏表示的图像压缩、去噪等(Sparse image coding method can be used for sparse representation-based image compression, denoising, et)
    2011-05-05 15:04:29下载
    积分:1
  • interface_migration1D
    FE solver for interface migration in 2phase problems
    2012-08-30 11:01:16下载
    积分:1
  • mathmodlingtoolbox
    数学建模绝对用的着,内有各种先进算法的matlab的m文件,绝对值得(very good material for you if you want toset up some math modles)
    2010-11-28 19:26:50下载
    积分:1
  • bayes_classify
    用Matlab编写的Bayes 分类器,用以进行两类模式识别(prepared using Matlab Bayesian classifier, used for two types of pattern recognition)
    2006-12-26 16:13:38下载
    积分:1
  • 06310047
    Quantitative Image Recovery From Measured Blind Backscattered Data Using a Globally Convergent Inverse Method
    2013-07-09 10:01:04下载
    积分:1
  • bbesselzerose
    bessel函数求零点,给一个参数x,则则可以求出x附近的bessel函数的零点。 (the bessel function evaluates 0:00, to the parameter x can be calculated bessel function of x near zero.)
    2012-08-29 22:59:57下载
    积分:1
  • Fourteen_bus
    基于matlab的标准ieee的14节点系统,运行正常。(standard IEEE fourteen node system based on matlab simulink, itis operating normally.)
    2014-11-13 20:26:33下载
    积分:1
  • semismth
    半光滑牛顿法semi-smooth Newton method(semi-smooth Newton method)
    2013-12-06 19:11:05下载
    积分:1
  • plot
    定义坐标轴的显示范围用axis指令 语法:axis([xmin xmax ymin ymax]) 你的例子ymin ymax应分别设为0和0.5,xmin xmax 取周期的两端。 然后再plot(x,y) 欢迎一起探讨matlab的使用:) (draw picture in matlab)
    2009-02-04 22:07:32下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载