BLDC1

Tool to load waveforms into a agilemt esg signal generator

chirp信号脉冲压缩，用于雷达信号处理，产生chirp信号后进行压缩，以实现高距离分辨力(chirp signal pulse compression for radar signal processing to generate chirp signal is compressed in order to achieve high range resolution)

本程序用Matlab语言实现了基于Arnold变换的图像置乱算法(this procedure using Matlab-based Arnold Transform Image Scrambling algorithm. .)

It acts in this TP of the regulation the speed of a D.C Motor with separated excitation, supplied with a chopper series, by using a regulator of the Proportional-Integral type (PI). The chopper is a static inverter allowing, starting a source of voltage U continues fixes, to obtain continuous a U_c voltage of variable median value. One uses a static switch for ` to chop ` the voltage continues and to feed a load. We will be interested in the particular case of a chopper series whose one can order the cyclic report/ratio α.

machine data processing part2

毫米波图像存在分辨率低的缺点，该程序在WRLA算法的基础上，进一步采用投影算法，能有效改善毫米波图像的分辨率(Images acquired from Passive Millimeter-Wave (PMMW) radiometer have poor resolution due to limited aperture dimension. Therefore, Super-Resolution Algorithm (SRA) is a key component for PMMW imager. SRA realizes spectrum extrapolation, however, spectrum in-band is deteriorated too. Wiener-Richardson-Lucy Algorithm (WRLA) recovers spectrum in-band by Wiener filter, and extrapolates spectrum out-of-band by Richardson-Lucy Algorithm (RLA). WRLA can avoid spectrum deterioration in passband, but its ability for spectrum extrapolation is limited also. We propose an improved algorithm to solve this problem. This algorithm, which has built constraints according to characteristics of PMMW imaging, uses Projection-Onto-Convex-Sets (POCS) technique to enhance the WRLA s performance, so it is termed as POCS-WRLA.)

基于语音信号的压缩感知重构程序 采用OMP算法对语音进行重构 包含语音的分帧程序，及omp程序，程序可正常运行。(Sensing Reconstruction program is based compressed speech signals Using OMP algorithm to reconstruct speech Framing program includes speech, and omp, programs can be run properly.)

首先,概述了太阳能光伏发电系统的组成,介绍了目前我国太阳能光伏发电技术的应用,并根据不同场合的需要,对太阳能光伏发电系统进行了分类。其次,分析了太阳能电池板的工作原理,利用州哄JLAB仿真软件对不同环境及 不同日照强度下的太阳能电池输出特性进行了建模!仿真结果证明了太阳能电池的非线性。再次,通过比较三种常用的DC/DC变换器的工作原理,提出利用BOOST型DqDC变换器实现转换,对参数进行分析后建立了BOOST型DC/DC变换器的仿真模型。最后,分析了最大功率点跟踪原理,比较了几种常用的最大功率点跟踪方法, 并在此基础上提出了一种新的扰动观察法,仿真结果表明了此方法的可行性。 (First, an overview of the composition of the solar photovoltaic power generation system, introduced the application of solar photovoltaic technology at present, and according to the needs of different occasions, for the solar photovoltaic system are classified. Secondly, the working principle of solar panels, the use of state coax JLAB simulation software for solar cell output characteristics of the different environments and under different sunlight intensity were modeled! Simulation results show that the nonlinear solar cells. Again, by comparing three common DC/DC converter works proposed use BOOST type DqDC converter to achieve the conversion, after the analysis of the parameters, the simulation model BOOST type DC/DC converter. Finally, the principle of maximum power point tracking, comparing several commonly used method for maximum power point tracking, and on this basis, we propose a new disturbance observation, simulation results show the feasibility of this method.)

说明：  通信原理在matlab上的实现，关于调制解调系统的各种部分(On communication theory in matlab implementation, on the various parts of modulation and demodulation system)

Matlab官方文档：统计工具箱statistics toolbox(Matlab official documents : Statistics Toolbox statistics toolbox)