Oguz_Ergin_iscturkey2008

此程序介绍了车牌识别中一个简单的神经网络识别案例，对于初学者具有较大帮助。(This program introduces a simple license plate recognition neural network case, have greater help for beginners.)

基于matlab的遗传算法的M文件，以前跟老师做srp项目时候找到的，很有用哦(Matlab genetic algorithm based on M-file)

该文件主要介绍如何应用matlab对控制系统进行数学描述与建模(This document describes how to use the control system matlab mathematical description and modeling)

数字基带系统的仿真，包含信号源的产生和眼图，已经仿真调试通过。(Simulation of digital baseband system, and the eye diagram contains the signal source, has been debugging through.)

说明：  基于matlab的LDPC码的encoding和decoding的程序，强烈推荐初学者学习参考(Matlab based on the LDPC code encoding and decoding procedures, strongly recommended reference for beginners to learn)

MATLAB遗传算法程序，主要用来求函数的极大值，可以修改后做其他的遗传算法方面的仿真(MATLAB genetic algorithm, the main function is to seek maximum value, after the simulation can be modified to do other aspects of genetic algorithms)

有关用MATLAB对语音时域进行分析的几种方法(Speech time-domain analysis of MATLAB in several ways)

本文件详细介绍了先进PID控制技术的发展，并附有matlab仿真程序。(This document details the development of advanced PID control technology, together with matlab simulation program.)

小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱（s1代表维修前的振动信号，s2代表维修后的振动信号），画出来进行对比，会发现s1信号的振动幅值会比较高；然后对s1和s2分别进行小波分解并画出各层的时域谱，只对比s1和s2分后的最高时域谱，s2更加的具有周期性，且幅值较小，s2周期性不够明显，且振动过于密集。分析完时域谱后开始分析频谱，首先对原信号s1和s2fft转换，得到频谱图，如图，然后再对小波分析后高频部分进行fft转换，做出频谱图。对比后我们发现，在f 2375HZ出（也就是齿轮的啮合频率），s1信号频谱幅值会有急剧的升高，然后，其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)

得到一些列的离散数据，用matlab，进行曲线拟合(Get some out of discrete data with matlab, for curve fitting)